@article { author = {Asadzadeh, V. and Dastfan, A. and Darabi, A.}, title = {Direct Torque-Control of PMSM Drive by Delayed Sliding Mode and Feedback Linearization Control Approach}, journal = {TABRIZ JOURNAL OF ELECTRICAL ENGINEERING}, volume = {49}, number = {2}, pages = {463-473}, year = {2019}, publisher = {Faculty of Electrical & Computer Engineering}, issn = {2008-7799}, eissn = {2538-3051}, doi = {}, abstract = {In this paper, performance improvement of a direct torque-controlled permanent-magnet synchronous motor drive is achieved through a novel delay dependent controller. The method is based on a delayed sliding controller with exponential reaching law in the outer speed loop combined with a nonlinear feedback linearization based controller in the inner flux and torque loop. Delayed sliding mode controller guarantees fast reaching to the sliding surface and avoids unwanted chattering due to its continuous approximation of the switching term in the sliding law. Simultaneously, the feedback linearization deals with motor nonlinearities and facilitates linear controller design for torque and flux regulation. The proposed scheme is based on the Lyapunov approach and utilizes space vector pulse width modulation with optimized design parameters. It provides fast torque and flux control with diminished fluctuations, high torque at low speed, fast speed response and reduced stator current distortions. Theoretical analysis and simulation results on a Siemens servo motor (1FT7082-AF7) prove the merits of the method in considering flux, torque and speed control performance compared with the conventional direct torque control based methods.}, keywords = {Permanent magnet synchronous motor,Direct torque control,delayed sliding mode controller,feedback linearization}, title_fa = {کنترل مستقیم گشتاور موتور سنکرون آهنربای دائم به روش مود لغزشی تاخیردار و خطی‌ساز فیدبک}, abstract_fa = {در این مقاله، کارایی درایو موتور سنکرون آهنربای دائم با کنترل مستقیم گشتاور ازطریق یک ساختار تنظیمی جدید وابسته به تأخیر بهبود یافته است. ساختار پیشنهادی مبتنی‌بر کنترل‌کننده مود لغزشی تأخیری با رسش نمایی در حلقه بیرونی سرعت است که با یک کنترل‌کننده خطی‌ساز فیدبک در حلقه داخلی شار و گشتاور ترکیب گشته است. کنترل مود لغزشی تأخیری به کمک رسش نمایی، همگرایی سریع حالت‌ها به سطح لغزش را تضمین می‌نماید و به سبب تقریب پیوسته‌ای که از تابع کلیدزن در قانون لغزش ارائه می‌دهد، از لرزش‌های ناخواسته جلوگیری کرده و خطای مانا را تقلیل می‌دهد. قانون فیدبک خطی‌ساز نیز به جبران‌سازی اثر غیرخطی دینامیک موتور پرداخته و امکان بهره‌گیری از کنترل‌کننده‌های خطی را برای حلقه شار و گشتاور ممکن می‌سازد. ساختار ترکیبی پیشنهادی از مدولاسیون بردار فضایی بهره برده، برمبنای تئوری لیاپانوف بنیان‌گذاری شده و ضرایب آن به‌صورت بهینه طراحی شده‌است که تمامی این ویژگی‌ها در کنار هم منجربه تولید گشتاور بالا در سرعت‌های پایین، کاهش ریپل شار و گشتاور و تقلیل اعوجاج جریانی در درایو موتور می‌شود. این روش ازطریق شبیه‌سازی بر روی موتور زیمنس (1FT7082-AF7) مورد آزمون قرارگرفته و با سایر روش‌های مشابه مبتنی‌بر کنترل مستقیم گشتاور مورد مقایسه قرار گرفته است.}, keywords_fa = {موتور سنکرون آهنربا دائم,کنترل مستقیم گشتاور,کنترل مود لغزشی تأخیردار,کنترل خطی‌ساز فیدبک}, url = {https://tjee.tabrizu.ac.ir/article_8853.html}, eprint = {https://tjee.tabrizu.ac.ir/article_8853_2c8fb6b13b97a1f4432d1560ff307d74.pdf} } @article { author = {Esfand Abadi, M. S. and Basti, F. and Shafiee, M. S.}, title = {Improved Multiband-Structured Subband Adaptive Filter Algorithm in Diffusion Distributed Networks}, journal = {TABRIZ JOURNAL OF ELECTRICAL ENGINEERING}, volume = {49}, number = {2}, pages = {475-484}, year = {2019}, publisher = {Faculty of Electrical & Computer Engineering}, issn = {2008-7799}, eissn = {2538-3051}, doi = {}, abstract = {Adaptive algorithms play an important role in order to improve performance of diffusion distributed network. In comparison of diffusion Normalized least mean square algorithm, family of diffusion subband algorithms have faster convergence rate when the input signal is highly correlated. This paper solves the problem of distributed estimation in the diffusion networks based on improved multiband-structured subband adaptive filter (IMSAF) and diffusion improved multiband structured subband adaptive filter (DIMSAF) is established. In proposed algorithm, convergence behavior improved due to using several input projections instead of single vector of input data. In addition, when the projection order is increased, the convergence rate of the proposed algorithm improves. The validity of the DIMSAF in comparison of DLMS, DAPA, VSS-DAPA and DRLS algorithms is demonstrated by several computer simulations. The results show fastest convergence rate.}, keywords = {adaptive filter,diffusion distributed networks,normalized subband,improved multiband-structured subband}, title_fa = {الگوریتم فیلتر تطبیقی زیرباند توسعه‌یافته در شبکه توزیع‌شده انتشاری}, abstract_fa = {الگوریتم‌های تطبیقی نقش مهمی در جهت بهبود عملکرد شبکه‌های توزیع‌شده انتشاری دارند. الگوریتم‌های خانواده زیرباند انتشاری در مقایسه با الگوریتم حداقل میانگین مربعات نرمالیزه‌شده انتشاری (DNLMS) دارای سرعت همگرایی بالاتری در مواجهه با ورودی رنگی هستند. این مقاله به ارائه مسأله تخمین توزیع‌شده در یک شبکه انتشاری برپایه الگوریتم زیرباند توسعه‌یافته (IMSAF) پرداخته و الگوریتم فیلتر تطبیقی زیرباند توسعه‌یافته انتشاری (DIMSAF) را معرفی می‌کند. در الگوریتم پیشنهادی برخلاف الگوریتم زیرباند نرمالیزه‌شده انتشاری (DNSAF)، به‌جای به‌کارگیری تک بردار رگرسور ورودی در هر زیرباند، از چند بردار رگرسورهای سیگنال ورودی استفاده می‌شود که این عمل منجر به بهبودی رفتار همگرایی الگوریتم پیشنهادی در مواجهه با ورودی رنگی خواهد شد. در این الگوریتم هرچه تعداد رگرسور ورودی بیشتر گردد، سرعت همگرایی نیز افزایش می‌یابد. عملکرد الگوریتم DIMSAF با الگوریتم‌های DLMS، DAPA، VSS-DAPA و DRLS مورد مقایسه قرار گرفته است. نتایج نشان می‌دهد عملکرد الگوریتم ارائه‌شده دارای سرعت همگرایی بالاتری در مقایسه با الگوریتم‌های ذکرشده است. }, keywords_fa = {فیلتر تطبیقی,شبکه‌های توزیع‌شده انتشاری,زیرباند نرمالیزه,زیرباند نرمالیزه توسعه‌یافته}, url = {https://tjee.tabrizu.ac.ir/article_9126.html}, eprint = {https://tjee.tabrizu.ac.ir/article_9126_4cbedcc68212b07862f0152e1b1beda2.pdf} } @article { author = {Omidvar, R. and Nejatian, S. and Parvin, H. and Rezaei, V. and Yasrebi, M.}, title = {A Nature-inspired Algorithm based on Classical-conditioning Theory}, journal = {TABRIZ JOURNAL OF ELECTRICAL ENGINEERING}, volume = {49}, number = {2}, pages = {485-501}, year = {2019}, publisher = {Faculty of Electrical & Computer Engineering}, issn = {2008-7799}, eissn = {2538-3051}, doi = {}, abstract = {Nature-inspired algorithms are the imitation of nature opened a new era in calculations for solving optimization problems. In this thesis, we will provide an optimization algorithm inspired by nature using the instinctive behavior of birds. In this thesis, particles learn to have a conditional normal behavior towards an unconditioned stimulus using the classical conditioning learning behavior of birds. Particles will be divided into multiple categories in the problem space. If any particle had a low-level category, it will try to move towards its best personal experience. If any particle had a high-level category, it will learn to move towards the global optimum in its category. Using the idea of birds’ sensitivity towards the environment, in which birds are flying, we tried to move particles in incompetent spaces more quickly so that the particle goes far away from that space, and vice versa, we will bring down the particles’ speed in valuable spaces to search for more. We selected a population based on the particles’ merit in the initial population selection using the instinctive behavior of birds. The proposed method was implemented in MATLAB software, and the results have been compared in several different ways. The results showed that the proposed method is a reliable algorithm to solve the static problems.}, keywords = {PSO Algorithm,optimization,particles cost,velocity equation,classical conditioning}, title_fa = {یک الگوریتم الهام‌گرفته از طبیعت مبتنی بر نظریه شرطی‌سازی کلاسیک}, abstract_fa = {الگوریتم‌های فرا ابتکاری الهام‌گرفته از طبیعت که به تقلید از طبیعت می‌باشند، یک دوره جدید را در حل مسائل بهینه‌سازی باز کردند. در این مقاله با استفاده از رفتار یادگیری شرطی‌سازی کلاسیک پرندگان، ذرات یاد می‌گیرند یک رفتار طبیعی شرطی را در قبال یک محرک غیرشرطی انجام دهند. ذرات در فضای مسئله به چندین دسته تقسیم خواهند شد و هر ذره اگر تنوع دسته خود را در سطح پایینی دید، سعی خواهد کرد به سمت بهترین تجربه شخصی خود حرکت کند و اگر سطح تنوع دسته بالا بود ذره یاد خواهد گرفت که در این شرایط به سمت بهینه عمومی دسته خود متمایل شود. همچنین با استفاده از ایده حساسیت پرندگان نسبت به فضایی که در آن پرواز می‌کنند، سعی شده که ذرات در فضاهای نامناسب با سرعت بیشتری به‌حرکت درآمده تا ذره از آن فضا دور گردد و بالعکس در فضاهای پرارزش سرعت ذرات جهت جستجوی بیشتر، پایین خواهد آمد. در جمعیت‌دهی اولیه نیز با استفاده از رفتار غریزی پرندگان، یک جمعیت‌دهی براساس شایستگی ذرات انجام خواهد شد. روش پیشنهادی در نرم‌افزار متلب پیاده‌سازی شده و نتایج در چندین بخش با روش‌های مختلف مشابه مقایسه و نتایج حاکی از آن بوده که روش پیشنهادی یک الگوریتم قابل‌اتکا در حل مسائل بهینه‌سازی ایستا می‌باشد.}, keywords_fa = {الگوریتم پرندگان,بهینه‌سازی,هزینه ذرات,معادله سرعت,شرطی‌سازی کلاسیک}, url = {https://tjee.tabrizu.ac.ir/article_8878.html}, eprint = {https://tjee.tabrizu.ac.ir/article_8878_d7da4fc6f54c3fb53bf505fef2f3498e.pdf} } @article { author = {Babaei, S. and Molaei, S. and Salehi, M.}, title = {Modeling Information Diffusion in Bibliographic Multilayer Networks}, journal = {TABRIZ JOURNAL OF ELECTRICAL ENGINEERING}, volume = {49}, number = {2}, pages = {503-515}, year = {2019}, publisher = {Faculty of Electrical & Computer Engineering}, issn = {2008-7799}, eissn = {2538-3051}, doi = {}, abstract = {‌Nowadays, ‌most ‌of ‌information ‌systems ‌can ‌be ‌modeled ‌as ‌multilayer ‌networks ‌which ‌each ‌layer ‌includes‌ ‌some ‌nodes ‌connected ‌to ‌each ‌other ‌by ‌different ‌types of links. Information ‌diffusion ‌in ‌networks ‌is ‌the ‌subject ‌that ‌researchers ‌considered ‌recently ‌and ‌they ‌analyzed ‌and ‌modeled ‌this ‌process type ‌in ‌the networks. ‌Although most ‌of ‌researches ‌in this field have focused ‌on ‌single ‌layer ‌networks, ‌but ‌in ‌the ‌real ‌world, ‌because ‌of ‌the ‌complexity ‌of ‌relations, most ‌systems ‌must ‌be ‌modeled ‌as‌ ‌multilayer ‌networks. ‌In ‌the ‌previous ‌ ‌works, ‌there are ‌much simplification ‌in ‌problem ‌space, ‌like ‌projection ‌all ‌layer ‌into ‌one ‌layer ‌or ‌negligence ‌the ‌mutual ‌effect ‌of ‌nodes ‌in ‌different ‌layers. ‌So a‌ ‌new ‌effective ‌model ‌for ‌analyzing ‌diffusion ‌in ‌multilayer ‌networks ‌is ‌needed.‌ This ‌method is ‌focused ‌on ‌predict‌ing ‌diffusion ‌in ‌multilayer ‌networks, ‌with ‌considering ‌mutual ‌effect ‌of ‌different ‌layers ‌on ‌each other. ‌T‌he ‌most ‌important ‌specification ‌of ‌this ‌proposed ‌method, ‌is ‌the ‌ability ‌to ‌specify ‌power ‌of ‌all ‌layers ‌and ‌measuring ‌this ‌power ‌ ‌regardless ‌node''''‌s ‌similarity ‌or ‌difference. ‌In ‌fact, ‌this ‌model can determine the diffusion power ‌of ‌each ‌type of nodes. ‌The ‌model‌ is applied on two real bibliographic information networks, and experimentally demonstrated the effectiveness of ‌this ‌model‌ compared with ‌other‌ diffusion models.}, keywords = {Multilayer Networks,Information Diffusion,Multiplex Networks,Interconnected Networks,Diffusion Processes}, title_fa = {مدل‌سازی انتشار اطلاعات در شبکه‌های کتابشناسی چندلایه}, abstract_fa = {بسیاری از سیستم‌های اطلاعاتی را می‌توان به شکل شبکه‌ای چندلایه مدل کرد که هر لایه متشکل از تعدادی گره است و این گره‌ها با انواع مختلفی یال به یکدیگر مرتبط می‌شوند. اگرچه محققان در سال‌های اخیر به تحلیل انتشار اطلاعات در شبکه توجه نشان داده‌اند، اکثر این مطالعات به شبکه‌های تک‌لایه محدود بوده است. اما در دنیای واقعی به دلیل پیچیدگی روابط بین گره‌ها، عموماً شاهد وجود شبکه‌های چندلایه هستیم. کارهای پیشین، اغلب با ساده‌سازی‌های زیاد فضای مساله همراه هستند، مثلاً در بیشتر کارها تنوع گره‌ها و تأثیر متقابل آن‌ها نادیده گرفته شده است. روش پیشنهادی این مقاله با در نظر گرفتن تأثیر لایه‌های مختلف بر یکدیگر به پیش‌بینی انتشار در شبکه‌های چندلایه، می‌پردازد. مهم‌ترین ویژگی روش، این است که می‌تواند قدرت تأثیر تمامی لایه‌ها را مشخص کند و میزان این تأثیر را بدون توجه به شباهت یا تفاوت گره‌های هر لایه نسبت به هم، اندازه‌گیری نماید. مدل پیشنهادی بر روی دو مجموعه داده‌ی واقعی پیاده سازی و با سناریوهای مختلفی ارزیابی شده است. همچنین روند فعال شدن گره‌های مختلف را به دست آورده و با روند رشد واقعیشان در واقعیت مقایسه کردیم و نشان دادیم که روش پیشنهادی نسبت به روش‌های پیشین که تمامی گره‌ها را از یک نوع فرض می‌کردند، شباهت بیشتری به واقعیت دارد و می‌تواند راه مناسبی برای پیش‌بینی انتشار در شبکه‌های چندلایه باشد. }, keywords_fa = {شبکه‌ی چندلایه,انتشار اطلاعات,شبکه‌ی چندگانه,شبکه‌ی به‌هم‌متصل,فرآیندهای انتشار}, url = {https://tjee.tabrizu.ac.ir/article_8824.html}, eprint = {https://tjee.tabrizu.ac.ir/article_8824_9060b98924790693b6b584f044443b6c.pdf} } @article { author = {Bijari, A. and Sheikhi, M.}, title = {A 3.1-10.6 GHz Ultra-Wideband Low Noise Amplifier with Novel Input Matching Network}, journal = {TABRIZ JOURNAL OF ELECTRICAL ENGINEERING}, volume = {49}, number = {2}, pages = {517-529}, year = {2019}, publisher = {Faculty of Electrical & Computer Engineering}, issn = {2008-7799}, eissn = {2538-3051}, doi = {}, abstract = {In this paper, a two-stage common source low noise amplifier (LNA) with novel input matching network is presented for ultra-wideband (UWB) applications. The proposed input matching network employing the active feedback and an inductive network is proposed to achieve the wideband matching, low noise figure and high flatness gain simultaneously. The proposed LNA has been designed and simulated in the RF-TSMC CMOS 0.18 μm technology by Advanced Design System (ADS). The simulation results exhibit a flat power gain (S21) of 15±1 dB with a noise figure (NF) lower than 3.5 dB and an input impedance matching less than –10 dB over 3.1 to 10.6 GHz bandwidth. It consumes 10 mW from 1 V supply voltage and occupies 0.85 mm2.}, keywords = {Low noise amplifier,Input matching,Common source configuration,Active feedback}, title_fa = {تقویت‌کننده کم ‏نویز فرا پهن‏ باند GHz 1.6-3.10 با شبکه تطبیق ورودی جدید}, abstract_fa = {در این مقاله، یک تقویت‌کننده کم‏نویز (LNA) دوطبقه سورس‏‏مشترک با شبکه تطبیق ورودی جدید برای کاربردهای فرا پهن­باند (UWB) ارائه ‌شده است. شبکه تطبیق پیشنهاد‏شده با استفاده از فیدبک منفی فعال و یک شبکه سلفی، دستیابی همزمان به تطبیق امپدانس ورودی پهن‏باند، عدد نویز پایین و بهره یکنواخت بالا را فراهم کرده است. تقویت‏کننده کم‏نویز پیشنهادشده بر پایه فنّاوری µm 18/0 CMOS RF-TSMC طراحی و با استفاده از نرم‏افزار ADS شبیه‌سازی ‌شده است. این تقویت‏کننده در پهنای باند GHz 3.10-1.6، دارای بهره توان مستقیم (S21) dB 1±15، عدد نویز (NF) کمتر از dB 3.5 و تلفات بازگشتی ورودی (S11) کمتر از dB 10- است. توان مصرفی آن نیز mW 10 از منبع تغذیه V 1 بوده و مساحت مصرفی تراشه در حدود mm2 0.85 است.}, keywords_fa = {تقویت‌کننده کم‏نویز,تطبیق ورودی,آرایش سورس‏ مشترک,فیدبک فعال}, url = {https://tjee.tabrizu.ac.ir/article_9150.html}, eprint = {https://tjee.tabrizu.ac.ir/article_9150_490fd42650e5b45b88aafa2923af30d6.pdf} } @article { author = {Tootoonchian, F.}, title = {Performance Analysis of Wound Rotor Brushless Resolvers under Run out Fault}, journal = {TABRIZ JOURNAL OF ELECTRICAL ENGINEERING}, volume = {49}, number = {2}, pages = {531-538}, year = {2019}, publisher = {Faculty of Electrical & Computer Engineering}, issn = {2008-7799}, eissn = {2538-3051}, doi = {}, abstract = {Resolver is an electromagnetic position sensors. To ensure the performance of the resolver is not deteriorated by the eccentricities, pancake resolvers are employed in industrial applications. The accuracy of pancake resolvers is suspected to be influenced by run-out fault. In this paper, the effect of run-out fault on the accuracy of the wound rotor resolver is studied by 3-D time stepping finite element method (TSFEM). Then, the contribution of the resolver’s rotor and the secondary of rotary transformer (RT) in the detected error is determined. Based on the analysis, an optimized structure is proposed to decrease the effect of run out fault. Finally, the success of the optimization is validated using experimental tests on the prototype of the sensor.}, keywords = {Position sensor,wound-rotor brushless resolver,rotary transformer,run-out fault}, title_fa = {تحلیل عملکرد ریزالورهای بدون جاروبک رتور سیم‌پیچی شده، تحت خطای رانش محوری}, abstract_fa = {ریزالور، یک حسگر تعیین موقعیت زاویه­ای است. ریزالور معمولاً به­صورت پنکیک، روی محور موتور، نصب می­شود تا دقت آن در اثر خطاهای ناهم­محوری کاهش نیابد. این نوع نصب، سبب بروز خطای رانش محوری می­شود. در این مقاله، تاثیر وقوع خطای رانش محوری، با استفاده از تحلیل اجزای محدود سه­بعدی مورد­بررسی قرار می­گیرد. سپس، سهم جابه­جایی رتور ریزالور و ثانویه ترانسفورماتور گردان، در خطای موقعیت مطالعه می­شود . بر این اساس، راه­کاری برای کاهش تاثیرپذیری دقت ریزالور، از خطای رانش محوری، ارائه می­شود. در پایان، تاثیر بهینه­سازی صورت­گرفته با استفاده از آزمایش عملی روی نمونه آزمایشگاهی ریزالور تایید می­شود.}, keywords_fa = {حسگر موقعیت,ریزالور بدون جاروبک رتور سیم‌پیچی‌شده,ترانسفورماتور گردان,خطای رانش محوری}, url = {https://tjee.tabrizu.ac.ir/article_9156.html}, eprint = {https://tjee.tabrizu.ac.ir/article_9156_ae7f51ded482e5e2e8302dd7be3a7048.pdf} } @article { author = {Tohidi, S. and Mamipour Matanag, B. and Rostami, N.}, title = {A New Method for Direct and Discrete Control of the PMSG in a Wind Turbine without need to Coordinate Transform}, journal = {TABRIZ JOURNAL OF ELECTRICAL ENGINEERING}, volume = {49}, number = {2}, pages = {539-550}, year = {2019}, publisher = {Faculty of Electrical & Computer Engineering}, issn = {2008-7799}, eissn = {2538-3051}, doi = {}, abstract = {This paper proposes a new method for the discrete control of active power and stator flux of permanent magnet synchronous generator in wind turbine. The main idea of this method is discrete control of the active power and stator flux from the perspective of the flux and angular load vector and Only by knowing active power and stator flux, the desired stator flux vector for the next moment is predicted. Then in order to generate the reference voltage vector, the space vector modulation is used which stabilizes the switching frequency and reduces the power and flux ripples. In this method all the calculations are done only in the stator reference frame and there is no need for translation to other reference frames. Compared to the vector control, this method has high dynamic response. The rotor flux and several machine parameters, including the stator inductance, are not interfered in the equations, which improves the robustness controller. Also, there is no need for integral proportional controllers and their coefficients adjustment. In this paper, MATLAB software is used for simulations. Comparison of the results of proposed method and vector control method optimized by the particle swarm algorithm, validates the high dynamic response, reduced active power and the stator flux ripple and overshoot in the proposed method.}, keywords = {direct power control (DPC),vector control,flux space vector,load angle analysis,permanent magnet synchronous generator (PMSG),wind Turbine}, title_fa = {روش‌جدیدکنترل مستقیم و گسسته‌زمان توان PMSG در توربین بادی بدون‌نیاز به تبدیل دستگاه مرجع}, abstract_fa = {این مقاله روش جدیدی برای کنترل گسسته‌زمان توان اکتیو و شار استاتور ژنراتور سنکرون مغناطیس دائم در توربین بادی پیشنهاد می‌کند. ایده اصلی این روش کنترل گسسته‌زمان توان اکتیو و شار استاتور از دیدگاه بردار فضایی شار و زاویه بار است و تنها با دراختیارداشتن اطلاعات توان اکتیو و شار استاتور، بردار مطلوب شار استاتور برای لحظه بعد پیش‌بینی شده، سپس از مدولاسیون بردار فضایی به‌منظور تولید بردار ولتاژ مرجع استفاده می‌شود که این‌کار موجب تثبیت فرکانس کلیدزنی و کاهش ریپل توان و شار می‌شود. در این روش کلیه محاسبات تنها در قاب مرجع استاتور انجام می‌شود و نیازی به تبدیل در قاب مرجع‌های دیگر وجود ندارد. این روش در مقایسه با روش کنترل‌برداری سرعت پاسخ‌دینامیکی بالایی دارد و همچنین، شار روتور و چندین پارامتر ماشین از جمله اندوکتانس استاتور در معادلات دخالت داده نمی‌شوند که موجب بهبود استحکام کنترل‌کننده می‌شود. همچنین نیازی به کنترل‌کننده‌های تناسبی‌انتگرالی و تنظیم ضرایب آن نیست. در این مقاله برای شبیه‌سازی از نرم‌افزار MATLAB استفاده شده‌است. مقایسه نتایج بین روش پیشنهادی و روش کنترل برداری که توسط الگوریتم تجمع ذرات بهینه‌سازی شده‌است، تأییدکننده سرعت بالای پاسخ دینامیکی و کاهش ریپل و فراجهش در توان اکتیو و شار استاتور در روش پیشنهادی است.}, keywords_fa = {کنترل مستقیم توان,کنترل برداری,بردار فضایی شار,تحلیل زاویه بار,ژنراتور سنکرون مغناطیس‌دائم,توربین بادی}, url = {https://tjee.tabrizu.ac.ir/article_8911.html}, eprint = {https://tjee.tabrizu.ac.ir/article_8911_53c41f4b7220efebdb2fcf031ab9eb74.pdf} } @article { author = {Hojjati, S. H. and Ebrahimzadeh, A. and Khazaee, A. and Babajani-Feremi, A.}, title = {Predicting Alzheimer's Disease using Soft Computing Feature selection algorithms and Based on rs-fMRI and sMRI}, journal = {TABRIZ JOURNAL OF ELECTRICAL ENGINEERING}, volume = {49}, number = {2}, pages = {551-563}, year = {2019}, publisher = {Faculty of Electrical & Computer Engineering}, issn = {2008-7799}, eissn = {2538-3051}, doi = {}, abstract = {Alzheimer’s disease (AD), a progressive, irreversible neurodegenerative disorder, occurs most frequently in older adults and gradually destroys regions of the brain that are responsible for memory, thinking, learning, and behavior. In this paper, AD prediction is investigated based on rs-fMRI and sMRI analysis. Three feature selection algorithms based on soft computing method has been proposed to classify MCI-C from MCI-NC through training SVM. This is the first study used to integrate rs-fMRI and sMRI for AD prediction. The results refer to the significant brain areas (functional and structural) impaired in AD. Furthermore, NBS method on brain functional parcellations has been utilized for separating MCI-C from MCI-NC and detecting the discriminative ability networks for AD prediction. }, keywords = {Alzheimer’s disease,Predicting,Graph theory,statistical information,sMRI,network based analysis}, title_fa = {پیش‌بینی بیماری آلزایمر با استفاده از الگوریتم‌های انتخاب ویژگی محاسبات نرم و بر پایه rs-fMRI و sMRI}, abstract_fa = {بیماری آلزایمر (AD)، یک بیماری پیشرفته و غیرقابل‌برگشت است که اغلب در افراد مسن رخ می‌دهد و به‌تدریج مناطق مغز را که مسئول حافظه، تفکر، یادگیری و رفتار هستند، از بین می‌برد. در این مقاله پیش‌بینی AD  بر اساس تصاویر rs-fMRI و sMRI بررسی می‌شود. در این مطالعه سه الگوریتم انتخاب ویژگی بر اساس روش محاسبات نرم ارائه شده، که طبقه‌بندی MCI-C از MCI-NC با آموزش و آزمایش الگوریتم SVM انجام می‌شود. این اولین مطالعه‌ای است که از ادغام rs-fMRI و sMRI برای پیش‌بینی AD استفاده کرده است. نتایج حاصل از این مطالعه می‌تواند به مناطق شناخته شده مغز )عملکردی و ساختاری( که در بیماری آلزایمر دچار اختلال شده‌اند، منجر شود. علاوه بر این، روش NBS بر روی تقسیم‌بندی‌های عملکردی مغز، برای جداسازی MCI-C از MCI-NC و تشخیص زیر شبکه‌هایی که دارای قابلیت تشخیصی برای پیش‌بینی AD هستند، به کار گرفته شده است.}, keywords_fa = {بیماری آلزایمر,پیش‌بینی,تئوری گراف,اطلاعات آماری مغز,تصویربرداری تشدید مغناطیسی,آنالیز مبتنی بر شبکه}, url = {https://tjee.tabrizu.ac.ir/article_9157.html}, eprint = {https://tjee.tabrizu.ac.ir/article_9157_0403a349eb264409c1b49f0c1068d95b.pdf} } @article { author = {Derakhshan, M. and Marvi, H. and Hassan poor, H.}, title = {Providing an Adaptive Model with two Adjustable Parameters for Audio Event Detection and Classification in Environmental Signals}, journal = {TABRIZ JOURNAL OF ELECTRICAL ENGINEERING}, volume = {49}, number = {2}, pages = {565-576}, year = {2019}, publisher = {Faculty of Electrical & Computer Engineering}, issn = {2008-7799}, eissn = {2538-3051}, doi = {}, abstract = {Audio event detection (AED) is a modern way to collect data about human activities in the workplace or in other life environments. We proposed a novel adaptable model based on using two parameters, α and ᵦ to detect all audio events that may be present in a given record accompanied by their time limits in which they occur. After feature extraction and setting the values of the two key parameters, alpha and beta, the audio sequence will be sent into two distinct sub-systems for event detection. The outputs from the two sub-classifiers are then combined and necessary refinements are made on the event time limits. The final detected events are sent to the KNN classifier. The parameters serve as a trade-off tool between precision and recall expectation in the detection process. In the tests, 16 different audio events of an office room were detected, some being similar to each other and some have very similar characteristics to those of the background noise. At frame-based (FB) level, the precision rate was 70.1%, the rate of recall was 75.8%, and F1-measure was 72.8%. The F1-measure has increased by 10.8% suggesting promising applications of the model.}, keywords = {Audio event detection (AED),environmental sounds,unsupervised learning,adaptable modeling systems,audio monitoring systems,audio-based acquisition systems}, title_fa = {ارائه یک مدل پارامتریک تطبیقی جهت کشف و رده‌بندی وقایع صوتی در سیگنال‌های محیطی}, abstract_fa = {کشف وقایع صوتی در محیط کار و زندگی یک نیاز مدرن جهت گردآوری اطلاعات است. تاکنون بیشتر تحقیق‌ها بر واقعه صوتی خاص و یا تعداد محدودی از وقایع صوتی برجسته متمرکز بوده‌است. در اینجا یک مدل‌سازی جدید جهت کشف تمام وقایع صوتی رخ‌داده در رکورد و تعیین محدوده زمانی برای هر یک از آن‌ها ارائه شده‌است. نوآوری شامل مدل‌سازی جدید همراه با پارامترهای تطبیقی در مدل است. پس از استخراج ویژگی‌ها و تعیین مقادیر دو پارامتر آلفا و بتا از دو قطعه‌بندی مجزا و ترکیب خروجی آن‌ها برای تعیین وقایع صوتی و محدوده زمانی آن‌ها استفاده شده‌است. این وقایع جهت رده‌بندی به الگوریتم KNN فرستاده می‌شوند. پارامترها امکان دقت بیشتر و یا میزان کشف حداکثری را ممکن می‌سازند. وقایع صوتی آزمایش‌شده شامل 16 نوع صدای اتاق کار اداری هستند که برخی شبیه هم و بعضی نیز مشابه نویز محیط هستند. در سنجش عملکرد برحسب واقعه، میزان درستی کشف 70.1 درصد، فراخوانی 75.8 درصد و میزان F1، 72.8 درصد بوده‌است. همچنین میزان F1 برحسب فریم 80.6 درصد حاصل شد. مقدار F1 برحسب واقعه، نسبت به قبل 10.8% بهبود داشته‌است که مویدکارآمدی مدل پیشنهادی است.}, keywords_fa = {کشف وقایع صوتی,صداهای محیطی,الگوریتم‌های یادگیری بدون نظارت,سیستم‌های پارامتریک تطبیقی,سیستم‌های نظارت صوتی,سیستم‌های کسب اطلاعات مبتنی بر صدا}, url = {https://tjee.tabrizu.ac.ir/article_9103.html}, eprint = {https://tjee.tabrizu.ac.ir/article_9103_b458624db4d5eabbd32674d874373062.pdf} } @article { author = {Dehghani, F. and Pourrostam, J.}, title = {Improving Jain Fairness Index and Optimizing Transmitter Power Consumption in NOMA Systems.}, journal = {TABRIZ JOURNAL OF ELECTRICAL ENGINEERING}, volume = {49}, number = {2}, pages = {577-586}, year = {2019}, publisher = {Faculty of Electrical & Computer Engineering}, issn = {2008-7799}, eissn = {2538-3051}, doi = {}, abstract = {In this paper, an approach is proposed for power allocation in Non-orthogonal multiple access (NOMA) systems in downlink to achieve user fairness from user capacity perspective and to optimize transmitter power consumption as well. In recent works, researchers have defined optimization problems and solved them, as in a method called Fair-NOMA, to maximize the capacity of each user in NOMA compared to OMA but the difference between the capacity of users and optimizing the transmitter power consumption are not considered. In this paper, a NOMA system with 2 and more than 2 users in downlink is considered. In the 2-user scenario by equating capacities of users, the Jain fairness index is maximized, fairness is achieved in transmitter power consumption and the difference between the capacities of users is eliminated. In addition, computer simulations show that the capacity of the user with weaker channel gain improves noticeably. Moreover, in a NOMA system with more than 2 users a fixed power coefficient is allocated to the user with the weakest channel condition, and power allocation to the other users is done in a way that the transmitter power consumption is optimized. Computer simulations is carried out to verify the effectiveness of the suggested methods.}, keywords = {Non orthogonal multiple access (NOMA),power allocation,jain fairness index,ergodic capacity,outage probability}, title_fa = {بهبود شاخص عدالت جین و بهینه‌سازی مصرف توان فرستنده در سیستم‌های NOMA}, abstract_fa = {در این مقاله روشی برای تخصیص توان سیستم‌های دسترسی چندگانه نامتعامد (NOMA) در لینک فروسو ارائه شده‌است، به‌گونه‌ای‌که عدالت بین کاربران از نظر ظرفیت هر کاربر تأمین شده و هم‌چنین توان فرستنده نیز به‌صورت بهینه مصرف شود. در پژوهش‌های گذشته برای این منظور عمدتاً به تعریف مسائل بهینه‌سازی و حل آن‌ها پرداخته شده‌است و یا مانند روشی با عنوان Fair-NOMA تنها به بیشینه‌کردن ظرفیت کاربران در مقایسه با یک سیستم دسترسی چندگانه متعامد (OMA) توجه شده اما اختلاف ظرفیت کاربران و هم‌چنین بهینه‌بودن مصرف توان فرستنده درنظر گرفته نشده است. در این مقاله یک سیستم NOMA در لینک فروسو با 2 و بیشتر از 2 کاربر در نظر گرفته شده‌است. در حالت 2 کاربری با مساوی قراردادن ظرفیت کاربران، شاخص عدالت جین بیشینه و عدالت بین کاربران در مصرف توان فرستنده برقرار گشته است و مشکل اختلاف ظرفیت کاربران حل شده‌است. هم‌چنین با شبیه‌سازی‌های رایانه‌ای نشان داده می‌شود که ظرفیت کاربر با شرایط کانال ضعیف‌تر با این روش بهبود قابل‌قبولی می‌یابد. علاوه‌براین، در سیستم NOMA با بیش از 2 کاربر با تخصیص یک ضریب توان ثابت به کاربری که ضعیف‌ترین شرایط کانال را دارد، توان به‌گونه‌ای به سایر کاربران تخصیص داده می‌شود که مصرف توان فرستنده بهینه شود. شبیه‌سازی‌های مختلف برای مقایسه و نشان‌دادن موثربودن ایده‌های پیشنهادی ارائه شده‌است.}, keywords_fa = {دسترسی چندگانه نامتعامد,تخصیص توان,شاخص عدالت جین,ظرفیت متوسط,احتمال وقفه}, url = {https://tjee.tabrizu.ac.ir/article_9130.html}, eprint = {https://tjee.tabrizu.ac.ir/article_9130_51d72b5af630338b50a6c2cf5f59d334.pdf} } @article { author = {Rahimi, M. and Haghi, A. and Belali, M.}, title = {Comparison of Machine side Converter Control Methods in PMSG based Wind Turbines}, journal = {TABRIZ JOURNAL OF ELECTRICAL ENGINEERING}, volume = {49}, number = {2}, pages = {587-599}, year = {2019}, publisher = {Faculty of Electrical & Computer Engineering}, issn = {2008-7799}, eissn = {2538-3051}, doi = {}, abstract = {Wind turbine-generators shaft is relatively soft and wind turbine mechanical systems is usually represented as two mass model. Two mass model contains torsional oscillatory modes that may be excited under wind speed variations and grid fault conditions. In this state, torsional oscillations may appear on the output responses of the wind turbine-generator. PMSG based WTs include two converters: machine side converter (MSC) and grid side converter (GSC). The main function of the GSC is the dc-link voltage regulation. Also, the MSC is used to control the generator speed or active power, and thus the control of the generator is mainly carried out by the MSC. There are different strategies for the control of MSC. The purpose of this paper is to study different control strategies of the MSC in the PMSG based WTs. These control strategies include turbine-generator control in speed control mode, power control mode or optimum tip speed ratio mode. Then, performance of the WT by using the mentioned control strategies against wind speed changes, aerodynamic power fluctuations due to tower shadow effect and grid voltage dip is examined and compared. Next, by modifying the MSC control, the wind turbine response is improved.}, keywords = {Permanent magnet synchronous turbine-generator,shaft torsional torque oscillations,machine side converter control,speed control,tower shadow}, title_fa = {مقایسه روشهای کنترل مبدل سمت ماشین در توربین-ژنراتور بادی مبدل کامل با ژنراتور سنکرون مغناطیس دائم}, abstract_fa = {محور توربین- ژنراتورهای بادی نسبتاً نرم بوده و سیستم مکانیکی عموماً به‌صورت دو‌جرمه مدل می‌شود. مدل دو‌جرمه دارای مدهای پیچشی نوسانی است که در‌هنگام تغییرات سرعت باد و وقوع خطا در شبکه این مدها در پاسخ‌های خروجی ژنراتور ظاهر می‌شود. توربین-ژنراتورهای بادی سنکرون مغناطیس دائم دارای مبدل‌های سمت ماشین و سمت شبکه است که به‌وسیله مبدل سمت ماشین می‌توان سرعت/توان ژنراتور را در مقدار مطلوب جهت کارکرد در مد توان بهینه کنترل نمود. در حقیقت کنترل اصلی توربین بر‌عهده مبدل سمت ماشین است. همچنین به‌وسیله مبدل سمت شبکه ولتاژ لینک dc در مقدار مرجع ثابت نگه داشته‌می‌شود. هدف این مقاله، تبیین استراتژی‌های مختلف کنترلی مبدل سمت ماشین در توربین- ژنراتور بادی سنکرون مغناطیس دائم است. استراتژی‌های مختلف کنترلی شامل کنترل توربین-ژنراتور در مد کنترل سرعت، مد کنترل توان و یا مد نرخ سرعت نوک بهینه می‌باشد. سپس عملکرد روش‌های کنترلی شرح‌داده‌شده، در‌ازای تغییرات سرعت باد، نوسانات توان ناشی از سایه برج و افتادگی ولتاژ شبکه آزموده و مقایسه می‌شود. در ادامه با بهبود عملکرد کنترل کننده مبدل سمت ماشین، پاسخ توربین بادی بهبود داده‌می‌شود}, keywords_fa = {توربین- ژنراتور سنکرون مغناطیس دائم,نوسانات گشتاور پیچشی شفت,کنترل مبدل سمت ماشین,کنترل سرعت,سایه برج}, url = {https://tjee.tabrizu.ac.ir/article_9153.html}, eprint = {https://tjee.tabrizu.ac.ir/article_9153_f568f5e63ec4370bdef2258c507c02f2.pdf} } @article { author = {Rashtchi, V. and Mousavi, H.}, title = {Countermeasure cryptography algorithm by PLL to FPGA}, journal = {TABRIZ JOURNAL OF ELECTRICAL ENGINEERING}, volume = {49}, number = {2}, pages = {601-612}, year = {2019}, publisher = {Faculty of Electrical & Computer Engineering}, issn = {2008-7799}, eissn = {2538-3051}, doi = {}, abstract = {Now days, sharing data in communication systems and computers require high levels of Information security. Side channel attack is one of the methods which it is applied to attack cryptographic systems such as smart cards. In this paper, a new approach for countermeasuring cryptographic algorithms has been proposed and implemented on FPGA. The scheme is based on using Phase Locked Loop in AES algorithm which by disturbing power consumption pattern and execution time of different rounds, the resistance of the algorithm against power attack has been increased. Masking and hiding technique has been used to protect the encryption key. Overall, the proposed method has been simulated within TSMC 65nm technology platform and outstanding success has been obtained; in applying the technique to AES, the overhead was 13% in CMOS area, 15% in power consumption, 2% decrease in working frequency while finding the key became difficult for attackers. In addition, the proposed method has been implemented on FPGA and satisfactory results have been obtained for an acceptable number of samples of the power trace.}, keywords = {Advanced Encryption Standard (AES),Differential Power Analysis (DPA),Power Analysis (PA),power measurement,Field Programmable Gate Array (FPGA)}, title_fa = {مقاوم‌سازی الگوریتم‌های رمزنگاری در داخل FPGA به کمک PLL}, abstract_fa = {امروزه اشتراک اطلاعات در سیستم‌های مخابراتی و کامپیوترها نیازمند امنیت بسیار بالایی است. در این میان، حملات کانال جانبی همواره به‌عنوان یکی از چالش‌های امنیتی در رمزنگاری سیستم‌ها می‌باشد، که برای حمله به ادوات رمزنگاری ازجمله کارت‌های هوشمند بکار می‌رود. در این مقاله هدف ارائه طرح جدیدی برای مقاوم‌سازی الگوریتم‌های رمزنگاری است که به‌صورت سخت‌افزاری در FPGA  پیاده شده‌است. اساس این طرح استفاده از حلقه فاز قفل شده PLL در الگوریتم‌های رمزنگاری AES می‌باشد که با به هم‌زدن میزان توان مصرفی و زمان‌های اجرای بخش‌های مختلف الگوریتم، مقاومت الگوریتم‌های رمزنگاری را در برابر حملات توان بالا می‌برد. این روش از دو تکنیک masking و hiding برای حفاظت کلید خصوصی رمزنگاری استفاده می‌کند، طرح پیشنهادی در تکنولوژی TSMC 65nm شبیه‌سازی شده و موفقیت قابل‌توجه نشان داده است، به‌طوری‌که توانسته است در رمزنگاری AES با هزینه سربار  13% در فضای اشغالی CMOS و افزایش 15 درصدی توان مصرفی، تنها فرکانس کاری را به اندازه 2% کم کرده و امکان به دست آوردن کلید صحیح برای حمله‌کننده را بسیار سخت نماید. همچنین، روش پیشنهادی بر روی FPGA پیاده‌سازی شده‌است و نتایج رضایت‌بخشی بر روی تعداد قابل قبولی از نمودار توان به‌دست آمده‌است.}, keywords_fa = {استاندارد رمزنگاری پیشرفته (AES),پردازش توان تفاضلی,اندازه‌گیری توان,آرایه گیت‌های قابل‌برنامه‌ریزی(FPGA)}, url = {https://tjee.tabrizu.ac.ir/article_8826.html}, eprint = {https://tjee.tabrizu.ac.ir/article_8826_247aab3f6e61ab5bd96f2794c53ad1c5.pdf} } @article { author = {Ramezan Ghanbari, A. and Raie, A.}, title = {New Control Method, with the Aim of Optimizing the Efficiency of Half Bridge Converter under the load variations}, journal = {TABRIZ JOURNAL OF ELECTRICAL ENGINEERING}, volume = {49}, number = {2}, pages = {613-625}, year = {2019}, publisher = {Faculty of Electrical & Computer Engineering}, issn = {2008-7799}, eissn = {2538-3051}, doi = {}, abstract = {In this paper, a new multi-mode control method is proposed to optimize the efficiency of the half bridge converter under the load variations. Efficiency optimization is performed by only changing the control mode and without adding elements to the main converter structure. The control method uses the prominent control modes including asymmetrical, duty phase shift, pulse width modulation (PWM) and burst control. For the first time, three transition points between control modes, being the specific values of the load current, are analytically calculated based on full bridge converter power losses. Transition points are used as the criteria for allocating the control mode and are functions of the half-bridge converter parameters. The proposed method continuously compares the load current with the transition points and puts the converter in the control mode with the highest efficiency. Thus, the half-bridge converter efficiency is optimized in terms of control modes and over the load variations. The accuracy of the analytically determined transition points and superiority of the proposed control method to the previous ones is determined by illustrating the performance of the converter.}, keywords = {Half bridge converter,zero voltage switching (ZVS),multi-mode control,asymmetric control,duty phase shift control,PWM control,burst control}, title_fa = {روش کنترلی جدید با هدف بهینه‌سازی بازدهی مبدل نیم‌پل در تغییرات جریان بار}, abstract_fa = {در این مقاله روش کنترلی چندحالته‌ی جدیدی، با هدف بهینه‌سازی بازدهی مبدل نیم‌پل در تغییرات جریان بار پیشنهاد شده‌است. بهینه‌سازی بازدهی تنها با استفاده از تغییر حالت کنترلی و بدون اضافه کردن المان به ساختار اصلی مبدل صورت می‌گیرد. روش پیشنهادی از حالت‌های کنترلی مطرح، شامل حالت کنترلی نامتقارن، شیفت ضریب وظیفه، PWM متقارن و پالس منقطع استفاده می‌کند. برای اولین‌بار نقاط گذر بین حالت‌های کنترلی که مقادیر مشخصی از جریان بار هستند، به‌صورت تحلیلی و برمبنای مقایسه تلفات مبدل نیم‌پل در حالت‌های کنترلی مختلف، محاسبه می‌شوند. نقاط گذر به‌عنوان معیاری برای تغییر حالت کنترلی استفاده شده و تابعی از پارامترهای مبدل نیم‌پل هستند. در روش پیشنهادی، جریان بار در هر لحظه با نقاط گذر مقایسه شده و مبدل در حالت کنترلی با بالاترین بازدهی ممکن قرار می‌گیرد. بدین‌ترتیب بازدهی مبدل نیم‌پل، برحسب حالتهای کنترلی و در سراسر بازه تغییرات بار، بهینه می‌شود. صحت و دقت معادلات نقاط گذر و برتری روش پیشنهادی نسبت به روش‌های پیشین، با ارائه نتایج عملکرد آن نشان داده شده‌است.}, keywords_fa = {مبدل نیم‌پل,سوییچینگ در ولتاژ صفر(ZVS),کنترل چندحالته,کنترل نامتقارن,کنترل شیفت ضریب وظیفه,کنترل PWM متقارن,کنترل پالس منقطع}, url = {https://tjee.tabrizu.ac.ir/article_9083.html}, eprint = {https://tjee.tabrizu.ac.ir/article_9083_06b942b465929962b16ea62d6b2fc1d6.pdf} } @article { author = {Zobeiri, M. and Mazloom-Nezhad Maybodi, B.}, title = {Introducing New Cryptography Method to Make Variable Ciphertext}, journal = {TABRIZ JOURNAL OF ELECTRICAL ENGINEERING}, volume = {49}, number = {2}, pages = {627-644}, year = {2019}, publisher = {Faculty of Electrical & Computer Engineering}, issn = {2008-7799}, eissn = {2538-3051}, doi = {}, abstract = {Through the passage of time, computer technology has been considered as a pivotal element in human life. Because of this point, it is more evident that information security gained a prominent position. Cryptography is utilized to secure information in a way that information became impenetrable under attack. In this paper, a new method of encryption is introduced according to the theoretical channel coding method and modular calculations. In this method, with the help of science of numerical theory and modular calculations, a method is used to generate dynamic permutation boxes and dynamic subsituation boxes. Then, with the help of information theory and coding, random errors are added to the text. Generated random errors should be detected and corrected at decryption time using decoding methods. The production of an independent cryptographic method with the pattern of intentional error use, along with the use of a shortcut key (256 bits), has the advantage of this method over the pattern-matching methods.This method can perform an encryption algorithm in which the performance of algorithm for a fixed text and a fixed encryption key, produce a differentiated encrypted text, with Hamming distance nearly 50%, in comparison to the previous performances.   }, keywords = {Block encryption,Modular calculations,Information theory and coding,Dynamic P-Box,Dynamic S-Box,Prime numbers,Symmetric key}, title_fa = {معرفی روش جدید رمزنگاری مبتنی بر تولید متن رمز شده متغیر}, abstract_fa = {با گذشت زمان، کامپیوتر در امور بیشتری از زندگی انسان رخنه می‌کند، به همین سبب در عصر کامپیوتر نیاز به حفاظت از اطلاعات شخصی بیش از پیش احساس می‌شود. علم رمزنگاری برای حفاظت از این اطلاعات بکار می‌آید، طوری که اگر سیستمی تحت حمله قرار گرفت امکان دسترسی به اطلاعات غیرممکن باشد. در این مقاله یک روش جدید رمزنگاری برای متن معرفی می‌گردد که ایده آن، استفاده از روش‌های تئوری کدینگ در رمزنگاری می‌باشد. در این روش به کمک علم تئوری اعداد و محاسبات پیمانه‌ای، یک روش جهت تولید جعبه‌های جایگشت پویا و جعبه‌های جانشینی پویا بکار گرفته می‌شود. در ادامه به کمک علم تئوری اطلاعات و کدینگ، خطاهای تصادفی عمدی به متن اضافه می‌گردد. خطاهای عمدی ایجاد شده می‌بایست در زمان رمزگشایی به کمک روش‌های دی‌کدینگ کشف و تصحیح شود. تولید یک روش مستقل رمزنگاری با الگوی استفاده از خطای عمدی در کنار استفاده از کلید رمزکوتاه (256 بیت)، مزیت این روش نسبت به روش‌های هم الگو می‌باشد. بعلاوه این روش قادر خواهد بود در هر بار اجرای الگوریتم رمزنگاری، برای یک متن آشکار ثابت و یک کلید رمزنگاری ثابت، متن رمز شده متفاوتی، با فاصله همینگ نزدیک به 50 درصد، نسبت به اجرای قبل تولید نماید. }, keywords_fa = {رمزنگاری بلوکی,محاسبات پیمانه‌ای,علم تئوری اطلاعات و کدینگ,جعبه‌جایگشت پویا,جعبه‌جانشینی پویا,اعداد اول,کلید رمزمتقارن}, url = {https://tjee.tabrizu.ac.ir/article_8850.html}, eprint = {https://tjee.tabrizu.ac.ir/article_8850_b51deb11cf9a5665958e79d51e2a660b.pdf} } @article { author = {Salarpour, A. and Khotanlou, H.}, title = {Line-Segment based Trajectory Similarity Measure using Time Warping Technique}, journal = {TABRIZ JOURNAL OF ELECTRICAL ENGINEERING}, volume = {49}, number = {2}, pages = {645-656}, year = {2019}, publisher = {Faculty of Electrical & Computer Engineering}, issn = {2008-7799}, eissn = {2538-3051}, doi = {}, abstract = {The most important issue with trajectory analysis is calculating similarity between trajectories. In this paper a novel method for measuring similarity between trajectories based on the cost to match a set of trajectories segments was introduced. The similarity between two trajectories is defined as a minimum cost to match a trajectory to the other one.  For this purpose, the segment based distance was introduced to as a cost of matching two trajectories segments. In addition, the dynamic programming technique is used to implement the time warp method. We performed some experiments to compare the proposed similarity measure with the similar approaches in the application of trajectory classification. The empirical quality of the proposed similarity measure was evaluated on 1-nearest neighbor (1-NN) classification task using 13 publicly available data sets. Compared to the other well-known similarity measures, the proposed method proved to be effective in the considered experiments based on the accuracy of classification.}, keywords = {Trajectory analysis,Similarity measure,Segment based distance,Time warping}, title_fa = {معیار شباهت مسیرهای حرکت مبتنی بر فاصله پاره خطی با استفاده از انحراف زمانی}, abstract_fa = {مهم‌ترین مسئله در آنالیز مسیر حرکت اجسام متحرک، به دست آوردن شباهت بین مسیرهای حرکت است. در این مقاله یک روش جدید برای اندازه‌گیری شباهت بین مسیرهای حرکت مبتنی بر هزینه تطبیق مجموعه پاره‌خط‌های مسیرهای حرکت به همراه تکنیک پیچ‌وتاب زمانی ارائه شده است. شباهت بین دو مسیر حرکت به عنوان حداقل هزینه لازم برای تطبیق یک مسیر حرکت به دیگری تعریف می‌شود. برای تطبیق یک مسیر حرکت به دیگری، فاصله پاره‌خطی به صورت میزان هزینه لازم برای تطبیق یک پاره‌خط به پاره‌خط دیگر، معرفی شده است. همچنین از تکنیک برنامه‌نویسی پویا برای پیاده‌سازی پیچ‌وتاب زمانی و حل مشکل انتقال مکانی استفاده شده است. معیار شباهت پیشنهادی به جای مقایسه مسیرها بر اساس مکان نقاط، از مقایسه پاره خط‌های مسیر سود می‌برد که کمک بیشتری به مقایسه ساختاری مسیرها می‌کند. به منظور ارزیابی روش پیشنهادی با روش‌های مشابه کاربرد آن را در طبقه بندی نزدیکترین همسایگی مسیر حرکت بررسی نموده‌ایم. نتایج آزمایش‌های انجام شده نشان می‌دهد معیار شباهت پیشنهادی در قیاس با روش‌های مشابه دارای صحت و میانگین رتبه بهتری است.}, keywords_fa = {آنالیز مسیر حرکت,معیار شباهت,فاصله پاره‌خطی,پیچ‌وتاب زمانی}, url = {https://tjee.tabrizu.ac.ir/article_8825.html}, eprint = {https://tjee.tabrizu.ac.ir/article_8825_6c27f3632b34b9f5e37365ec30a6bc2f.pdf} } @article { author = {Sadeghi, H. and Raie, Abolghasem-A.}, title = {Metric Learning based on Fast χ2 Distance for Histogram Data Classification via KNN Classifier}, journal = {TABRIZ JOURNAL OF ELECTRICAL ENGINEERING}, volume = {49}, number = {2}, pages = {657-668}, year = {2019}, publisher = {Faculty of Electrical & Computer Engineering}, issn = {2008-7799}, eissn = {2538-3051}, doi = {}, abstract = {Data comparison is a fundamental problem in machine learning research. Since, metric learning has various applications in clustering and classification problems, it is attracted much attention in the last decades. In this paper, an appropriate metric learning method is presented to utilize in machine vision problems. Common features in machine vision are often histogram; however, metric learning methods are usually designed based on Mahalanobis distance which is not applicable in histogram features. In this study, a new metric learning method based on modified chi-squared distance (χ2) for histogram data is presented. In histogram data classification, χ2 distance is more accurate than Euclidean one; however, its computational cost is higher than Euclidean distance. In this paper, a χ2 distance approximated formulation where a part of its computations is moved into the feature extraction step in offline phase is proposed. Consequently, computational cost of feature comparison is reduced. Experiments on different datasets show that the proposed metric learning method is more accurate than the existing ones in histogram data classification. Moreover, the approximated χ2 distance increases feature comparison speed about 2.5 times without loss of accuracy.}, keywords = {Metric learning,fast chi-squared distance,histogram classification,KNN classifier}, title_fa = {یادگیری متریک بر اساس فاصله χ2 سریع برای دسته‌بندی داده‌های هیستوگرامی با دسته‌بندی کننده KNN}, abstract_fa = {مقایسه داده‌ها یک مسأله بنیادی و پرکاربرد در یادگیری ماشین است. در دهه گذشته تحقیقات فراوانی در زمینه یادگیری متریک انجام شده است؛ از کاربردهای یادگیری متریک می‌توان به خوشه‌بندی و دسته‌بندی داده‌ها اشاره کرد. در این مقاله یک روش یادگیری متریک مناسب برای استفاده در مسائل بینایی ماشین ارائه می‌شود. اکثر ویژگی‌هایی که در بینایی ماشین استفاده می‌شوند، هیستوگرامی هستند؛ اما روش‌های یادگیری متریک اغلب بر مبنای فاصله ماهالانوبیس طراحی شده‌اند که در ویژگی‌های هیستوگرامی کارایی مناسبی ندارد. در این تحقیق یک روش جدید یادگیری متریک برای داده‌های هیستوگرامی بر مبنای فاصله مربع کای (χ2) اصلاح شده ارائه می‌شود. فاصله χ2 در دسته‌بندی داده‌های هیستوگرامی دارای دقت بالاتری نسبت به فاصله اقلیدسی است، اما هزینه محاسباتی آن نیز بالاتر است. در این مقاله یک رابطه تقریبی برای فاصله χ2 پیشنهاد می‌شود و بخشی از محاسبات را به مرحله استخراج ویژگی (که به‌صورت غیربرخط قابل محاسبه است) منتقل می‌کند؛ به این ترتیب سرعت مقایسه ویژگی‌ها افزایش می‌یابد. آزمایش‌ها بر روی پایگاه‌های داده مختلف نشان می‌دهد که روش یادگیری متریک پیشنهادی دارای دقت بالایی در دسته‌بندی داده‌های هیستوگرامی مختلف نسبت به روش‌های موجود است. همچنین معیار تقریبی برای فاصله χ2، با حفظ دقت، سرعت مقایسه داده‌ها را 2.5 برابر افزایش می‌دهد.}, keywords_fa = {یادگیری متریک,فاصله مربع کای سریع,دسته‌بندی هیستوگرام,دسته‌بندی کننده KNN}, url = {https://tjee.tabrizu.ac.ir/article_9128.html}, eprint = {https://tjee.tabrizu.ac.ir/article_9128_76226974e4b2759ca228ae9eeffff238.pdf} } @article { author = {Safdarian, A. and Ganjkhani, M. and Badakhshan, S.}, title = {Water Saving in Electricity Generation System: Potential and Cost}, journal = {TABRIZ JOURNAL OF ELECTRICAL ENGINEERING}, volume = {49}, number = {2}, pages = {669-680}, year = {2019}, publisher = {Faculty of Electrical & Computer Engineering}, issn = {2008-7799}, eissn = {2538-3051}, doi = {}, abstract = {Power plants have noticeable share from underground water consumption. In order to make some water savings, different approaches such as replacing wet cooling towers and installing renewable energy sources have been proposed. These medium and long term approaches however need huge investments and may degrade performance of the system. This paper discusses generation system water consumption minimization as a short term solution. To do so, conventional economic dispatch problem is extended to a multi-objective problem where a linear combination of electricity generation cost and water consumption is minimized. The paper presents estimation procedure of water saving cost function in a generation system. Then, a test system is applied to determine potentials and costs of saving water in a generation system. Different studies are conducted and the results are presented. Finally, water saving cost function is estimated for the generation system. According to the results, some relevant conclusions are drawn.     }, keywords = {Electric energy generation system,Underground water sources,economic dispatch,water consumption saving}, title_fa = {صرفه‌جویی آب در سیستم‌های تولید برق: پتانسیل و هزینه}, abstract_fa = {نیروگاه­ها سهم عمده­ای از مصرف آب­های زیرزمینی را به خود اختصاص می­دهند. به­منظور کاهش آب مصرفی در نیروگاه­ها، فعالیت­های مختلفی نظیر تبدیل برج­های تقطیر مرطوب نیروگاه­های حرارتی به برج­های تقطیر خشک و سرمایه­گذاری بر روی منابع انرژی تجدیدپذیر در صنعت برق کشور موردتوجه واقع شده است. لیکن، راه­کارهای مذکور به­عنوان راه­کار میان­مدت و بلندمدت با چالش­هایی نظیر هزینه سرمایه­گذاری بالا و افت بازده نیروگاه­های هدف همراه است. در این مقاله، کمینه­سازی آب مصرفی مجموعه نیروگاه­ها در شرایط بهره­برداری به­عنوان راه­کار کوتاه­مدت موردتوجه واقع شده است. بدیهی است که این راه­کار پتانسیل محدودی در صرفه­جویی آب داشته، لحاظ هدف مذکور افزایش هزینه تولید برق را در پی خواهد داشت. لذا، هدف این مقاله ارزیابی پتانسیل مذکور در صرفه­جویی و تخمین هزینه­های مربوطه است. به­منظور اجتناب از افزایش چشم­گیر هزینه­ها، مسئله توزیع اقتصادی توان به­صورت یک مدل چند تابع هدفه با هدف کاهش هزینه و آب مصرفی ارائه شده است. به این منظور، ابتدا مسئله توزیع اقتصادی توان با لحاظ آب مصرفی نیروگاه­ها مدل­سازی می­شود. سپس، روش حل مدل پیشنهادی تشریح می­گردد. در ادامه، روند استخراج تابع هزینه صرفه­جویی آب مصرفی سیستم­های تولید انرژی الکتریکی ارائه می­گردد. در انتها، مدل و روش ارائه­شده بر روی یک سیستم تولید نمونه پیاده­سازی شده و نتایج حاصله ارائه و مورد بحث واقع می­شود.}, keywords_fa = {سیستم تولید انرژی الکتریکی,منابع آب زیرزمینی,توزیع اقتصادی توان,صرفه‌جویی در مصرف آب}, url = {https://tjee.tabrizu.ac.ir/article_9155.html}, eprint = {https://tjee.tabrizu.ac.ir/article_9155_cc311ac2279dffb31824a56a8bdbe7e9.pdf} } @article { author = {Tahmasi, A. and Seifi Kavian, Y. and Kaabi, H.}, title = {Design and Hardware Implementing of Optical Physical Layer for Wireless Sensor Network Applications}, journal = {TABRIZ JOURNAL OF ELECTRICAL ENGINEERING}, volume = {49}, number = {2}, pages = {681-691}, year = {2019}, publisher = {Faculty of Electrical & Computer Engineering}, issn = {2008-7799}, eissn = {2538-3051}, doi = {}, abstract = {Wireless sensor network (WSN) consists of some small and cheap nodes which could communicate together, process gathered data, and sense the environment. Today’s developments in wireless communication systems, causes higher data rate for multimedia applications. The optical wireless communication (OWC) can provide higher data rates and more secured communication links rather that radio frequency (RF) technology for some applications such as underwater communications. In this paper, the optical technology is employed for data transmission in WSNs. An optical wireless sensor network (OWSN) is realized based on sensor nodes and cluster head (CH). Different hardware parts of designed sensor boards are evaluated and the optical communication parameters are measured. An optimized media access control protocol called VMAC is presented. In the proposed OWSN, both nodes and CH are modular. The experimental results show that the maximum transmission distance for 300bps and 600bps baud rates are 18m with 0% BER and 21m with 10% BER, respectively.}, keywords = {Wireless sensor network,optical wireless communication,radio frequency,media access control,bit error rate}, title_fa = {طراحی و پیاده‌سازی سخت‌افزاری لایه فیزیکی نوری برای کاربرد در شبکه حسگر بی‌سیم}, abstract_fa = {شبکه حسگر بی‌سیم متشکل از گره‌های ارزان، چندکاره و با اندازه کوچک هستند که می‌توانند عملیات حس کردن محیط، جمع‌آوری و پردازش داده و برقراری ارتباط را انجام دهند. امروزه با توسعه ارتباطات بی‌سیم، به نرخ‌داده بالاتری به‌ویژه برای کاربردهای چندرسانه‌ای نیاز است. ارتباطات بی‌سیم نوری (OWC) می‌تواند نرخ داده بالاتر و ارتباطی بسیار امن نسبت به ارتباط رادیوئی فرکانس بالا فراهم کنند و در کاربردهایی مانند ارتباطات نوری زیر آب بسیار مفید می‌باشد. در این مقاله یک شبکه حسگر بی‌سیم با توانایی انتقال داده به‌صورت نوری طراحی و ساخته شده‌است. قسمت‌های مختلف گره حسگر طراحی شده، به‌صورت عملی آزمایش می‌شود و سپس پارامترهای ارتباط نوری اندازه‌گیری خواهد شد. همچنین یک پروتکل دسترسی به رسانه مناسب شبکه حسگر بی‌سیم نوری مناسب ارائه می‌گردد. در شبکه حسگر بی‌سیم نوری طراحی شده، همه بخش‌های گره و سرخوشه ماژولار هستند بدین معنی که می‌توان فرستنده، گیرنده و حسگرها را دوباره طراحی و جایگزین کرد. نتایج آزمایش نشان می‌دهد که بیشینه فاصله انتقال داده با نرخ داده 300 و 600 بیت بر ثانیه برابر 18 متر با نرخ خطای بیتی صفر درصد و 21 متر با نرخ خطای بیتی 10 درصد می‌باشد.}, keywords_fa = {شبکه حسگر بی‌سیم,ارتباطات بی‌سیم نوری,ارتباط رادیوئی,پروتکل دسترسی به رسانه,نرخ خطای بیت}, url = {https://tjee.tabrizu.ac.ir/article_8854.html}, eprint = {https://tjee.tabrizu.ac.ir/article_8854_3c81a67d0f309e04bcda4fcf4ea12df8.pdf} } @article { author = {Amouei, S. and Mirzaie, K.}, title = {Vector Quantization Using a Modified Firefly Algorithm for Image Compression}, journal = {TABRIZ JOURNAL OF ELECTRICAL ENGINEERING}, volume = {49}, number = {2}, pages = {693-707}, year = {2019}, publisher = {Faculty of Electrical & Computer Engineering}, issn = {2008-7799}, eissn = {2538-3051}, doi = {}, abstract = {Vector Quantization (VQ) is the powerful technique in image compression. Generating a good codebook is an important part of VQ. There are various algorithms in order to generate an optimal codebook. Recently, Swarm Intelligence (SI) algorithms were adapted to obtain the near-global optimal codebook of VQ. In this paper, we proposed a new method based on a modified firefly algorithm (MFA) to construct the codebook of VQ. The proposed method merged genetic crossover operator with FA to develop the VQ. This method is called MFA model. Experimental results indicate that the reconstructed images generated by the proposed model is get higher quality than FA and it’s about one percent, but it is no significant superiority to the PSO algorithm. Furthermore, MFA is slower than FA.}, keywords = {Image Compression,Vector Quantization,Swarm Intelligence,Firefly Algorithm}, title_fa = {فشرده‌سازی تصویر توسط چندی‌سازی برداری مبتنی بر الگوریتم کرم‌ شب‌تاب بهبود‌یافته}, abstract_fa = {چندی‌سازی برداری یکی از روش‌های پرکاربرد در فشرده‌سازی تصویر است. پژوهشگران، الگوریتم‌های مختلفی با چندی‌سازی برداری به‌منظور رسیدن به کتاب-کد بهینه ارائه داده‌اند. ازجمله این الگوریتم‌ها می‌توان از الگوریتم ژنتیک، الگوریتم بهینه‌سازی ازدحام ذرات و الگوریتم کرم شب‌تاب نام برد. در این مقاله برای چندی‌سازی برداری، روش جدیدی بر اساس الگوریتم کرم شب‌تاب بهبودیافته ارائه‌شده است. در روش پیشنهادی عملگر ترکیب ژنتیک با الگوریتم کرم شب‌تاب پایه، به‌منظور بهبود الگوریتم پایه، ادغام‌شده و از آن در تولید کتاب-کد چندی‌سازی برداری، استفاده‌ گردیده است. نتایج پیاده‌سازی روش پیشنهادی، نشان ‌می‌دهد که این الگوریتم کرم شب‌تاب بهبودیافته در مقایسه با الگوریتم‌های ژنتیک و کرم شب‌تاب پایه، بهتر عمل ‌می‌کند. درصد بهبود کیفیت روش پیشنهادی نسبت به الگوریتم کرم شب‌تاب پایه حدود یک درصد است. علاوه بر آن، با افزایش سایز کتاب-کد عملکردی مشابه با الگوریتم بهینه‌سازی ازدحام ذرات دارد.}, keywords_fa = {فشرده‌سازی تصویر,چندی‌سازی برداری,الگوریتم ژنتیک,الگوریتم کرم شب‌تاب}, url = {https://tjee.tabrizu.ac.ir/article_9151.html}, eprint = {https://tjee.tabrizu.ac.ir/article_9151_e60df844ffd321de00be555b7ea061c6.pdf} } @article { author = {Eyvazi Adli, S. and Shoaran, M. and S. Noorani, S. M.}, title = {Position Based Visual Hovering Control of the AR.Drone 2.0 Quadcopter Using Fuzzy Logic}, journal = {TABRIZ JOURNAL OF ELECTRICAL ENGINEERING}, volume = {49}, number = {2}, pages = {709-720}, year = {2019}, publisher = {Faculty of Electrical & Computer Engineering}, issn = {2008-7799}, eissn = {2538-3051}, doi = {}, abstract = {Autonomous hovering of AR.Drone 2.0 quadcopter, which is an important subject and prerequisite for other autonomous UAV applications, is the goal of this paper. We propose a new method, called GSPnP, for pose estimation using only the bottom camera of the robot. Moreover, an optimal fuzzy controller, called TGM, is designed in order to stabilize the quadcopter hovering. Then, the optimal parameter values for the controller are obtained.The current position of the robot, relative to the ArUco library marker, is computed using our proposed GSPnP algorithm and the images of the bottom camera. The current position is sent to the controller and the output is computed based on the ROS AR.Drone 2.0 driver and is sent to the robot simulated in the Gazebo world. The results indicate a more accurate and desirable performance of GSPnP method and TGM fuzzy controller in controlling the robot position compared with other methods with an error of less than 30, 40, and 20 millimeters in x, y, and z directions, respectively.}, keywords = {Quadcopter AR.Drone 2.0,Autonomous hovering,PnP pose estimation,Fuzzy controller,Gazebo simulator,ROS}, title_fa = {کنترل موقعیت مبتنی بر بینایی کوادکوپترAR.Drone 2.0 شناور با استفاده از منطق فازی}, abstract_fa = {خودکارسازی شناوری کوادکوپتر AR.Drone 2.0 که موضوعی مهم و پیش‌نیاز سایر خودکارسازی‌ها است هدف این مقاله می‌باشد. در این مقاله الگوریتم جدیدی  به نام GSPnP برای تخمین موقعیت ربات پرنده با استفاده از تک دوربین پیشنهاد می‌گردد. همچنین یک کنترلر فازی بهینه موسوم به TGM برای پایدارسازی شناوری کوادکوپتر طراحی و پارامترهای بهینه کنترلر فازی تعیین می‌شوند. موقعیت فعلی کوادکوپتر نسبت به مارکر کتابخانه ArUco با پردازش تصاویر دوربین زیرین ربات توسط الگوریتم پیشنهادی GSPnP محاسبه و به کنترلر ارسال می‌شود. خروجی کنترلر بر اساس درایور ربات متعلق به سیستم عامل رباتیک (ROS) محاسبه شده و به ربات شبیه‌سازی شده در محیط شبیه‌سازی Gazebo ارسال می‌شود. نتایج به‌دست‌آمده نشان‌دهنده عملکرد دقیق‌تر و مطلوب‌تر روش GSPnP و روش کنترل فازی TGM با خطای کمتر از 30، 40 و 20 میلی‌متر در کنترل طول، عرض و ارتفاع نسبت به سایر روش‌ها، در کنترل موقعیت ربات است.}, keywords_fa = {کوادکوپتر AR.Drone 2.0,شناوری خودکار,تخمین موقعیت PnP,کنترلر فازی,شبیه‌ساز Gazebo,سیستم عامل رباتیک}, url = {https://tjee.tabrizu.ac.ir/article_8917.html}, eprint = {https://tjee.tabrizu.ac.ir/article_8917_11ba11df8848537fbe1992efc4c6d9cc.pdf} } @article { author = {Fazeli Asl, S.B. and Moosapour, S.S.}, title = {Fractional Order Dynamic Sliding Mode Controller Design for Triaxial Gyroscope based on Backstepping Method}, journal = {TABRIZ JOURNAL OF ELECTRICAL ENGINEERING}, volume = {49}, number = {2}, pages = {721-734}, year = {2019}, publisher = {Faculty of Electrical & Computer Engineering}, issn = {2008-7799}, eissn = {2538-3051}, doi = {}, abstract = {In this paper, a dynamic sliding mode controller with fractional order sliding surface based on backstepping algorithm is designed and presented for controlling performance of a micro-electro-mechanical triaxial gyroscope. To compensate uncertainties and incoming disturbances to the system, a sliding mode controller is used. In order to increase the degree of freedom and further robustness of the controller, the sliding surface is selected as fractional order form. Using dynamic sliding mode controller in addition to the increasing the performance of controller, cause to reduce the chattering phenomenon in the input control signal. Using the backstepping approach as a very powerful design tool for nonlinear systems, makes the designed controller more robust against incoming disturbances to the system. Asymptotic stability of the closed loop system will be proven by Lyapunov stability theorem. At the end of the design, in order to efficacious reduce the chattering phenomenon in the control signal, fuzzy control theory for control the boundary layer and also adaptive method for online estimating the upper bound of uncertainty are used. In order to evaluate performance of the designed controller, this controller is compared with two other sliding mode controllers. Simulation results show that the proposed controller have a much less chattering phenomenon in control signal, increasing system stability, reducing the rise time and better tracking.}, keywords = {Dynamic sliding mode,Fractional order,backstepping,adaptive,triaxial gyroscope}, title_fa = {طراحی کنترل‌کننده مد لغزشی دینامیکی مرتبه کسری تطبیقی برای سیستم ژیروسکوپ سه محوره بر اساس روش بازگشت به عقب}, abstract_fa = {در این مقاله، یک کنترل‌کننده مد لغزشی دینامیکی با سطح لغزش مرتبه کسری بر اساس الگوریتم بازگشت‌به‌عقب برای کنترل عملکرد ژیروسکوپ سه محوره میکرو الکترومکانیکی طراحی شده است. برای جبران نامعینی‌ها و اغتشاشات وارده به سیستم از کنترل‌کننده مد لغزشی استفاده می‌شود. به‌منظور افزایش درجه آزادی و مقاومت بیشتر کنترل‌کننده، سطح لغزش به‌صورت مرتبه کسری انتخاب می‌شود. استفاده از کنترل‌کننده مد لغزشی دینامیکی علاوه‌بر افزایش عملکرد کنترل‌کننده باعث کاهش پدیده چترینگ در سیگنال کنترل می‌شود. استفاده از روش بازگشت‌به‌عقب به‌عنوان یک ابزار طراحی بسیار قوی برای سیستم‌های غیرخطی، باعث مقاومت بیشتر کنترل‌کننده طراحی‌شده در برابر اغتشاشات وارده به سیستم می‌شود. پایداری مجانبی سیستم حلقه بسته با استفاده از تئوری پایداری لیاپانوف اثبات می‌شود. در پایان طراحی به‌منظور کاهش مؤثر پدیده چترینگ در سیگنال کنترل، از تئوری کنترل فازی برای لایه مرزی و همچنین از روش تطبیقی جهت تخمین آنلاین کران بالای عدم‌قطعیت استفاده شده است. به‌منظور ارزیابی کارایی کنترل‌کننده طراحی‌شده، این کنترل‌کننده با دو نوع کنترل‌کننده مد لغزشی دیگر مقایسه شده است. نتایج شبیه‌سازی نشان می‌دهد که کنترل‌کننده پیشنهادی دارای پدیده چترینگ یا نوسانات ناخواسته بسیار کمتر در قانون کنترل، افزایش پایداری سیستم، کاهش زمان صعود و ردیابی قابل‌قبول می‌شود.}, keywords_fa = {مد لغزشی دینامیکی,مرتبه کسری,بازگشت به عقب,تطبیقی,ژیروسکوپ سه محوره}, url = {https://tjee.tabrizu.ac.ir/article_9122.html}, eprint = {https://tjee.tabrizu.ac.ir/article_9122_6fcf80ccba4ec73626f8e9243070c2de.pdf} } @article { author = {Fargadi, Sh. and Miri, M. and Sheikhi, M. H.}, title = {Miniaturization and bandwidth enhancement of Mach-Zehnder polarization splitter using non-uniform multimode interferometers}, journal = {TABRIZ JOURNAL OF ELECTRICAL ENGINEERING}, volume = {49}, number = {2}, pages = {735-745}, year = {2019}, publisher = {Faculty of Electrical & Computer Engineering}, issn = {2008-7799}, eissn = {2538-3051}, doi = {}, abstract = {The design of a compact wideband polarization splitter based on Mach-Zehnder interferometer (MZI) with non-uniform multi-mode interferometer (MMI) couplers is presented in this manuscript. The polarization splitting in the proposed structure stems from polarization dependent dispersion of non-uniform silicon-on-insulator (SOI) waveguides used as the MZI arms. The use of non-uniform MMI couplers increases the bandwidth of the structure while reduces its sensitivity to fabrication imperfections. Our simulation results show the very low insertion loss of 0.8dB, and high polarization extinction ratios of 10dB and 15dB for transverse magnetic and transverse electric field polarization, respectively, in the ultra-wide bandwidth of 100nm (1500nm-1600nm). The proposed polarization splitter has wider bandwidth and larger fabrication tolerance compared to the directional coupler based splitter. In addition total footprint is 3.86×60mm2 which is much smaller than MZI based splitters.}, keywords = {Polarization beam splitter,Mach-Zehnder Interferometer (MZI),Silicon-On-insulator (SOI),Polarization Extinction ratio (PER)}, title_fa = {کوچک‌سازی و افزایش پهنای‌باند تفکیک‌کننده‌ قطبش ماخ – زندر با استفاده از تزویج‌گر چندمُدِ غیریکنواخت}, abstract_fa = {در این مقاله یک ساختار تفکیک­کننده­ی قطبش با چیدمان ماخ-زندر (MZI) ارائه شده که در آن از تزویج‌گرهای تداخل چندمُد (MMI) غیریکنواخت و بازوهای ناهمسان مبتنی بر موجبر SOI استفاده شده است. تداخل سازنده و یا مخرب برای دو قطبش مختلف نور ورودی و درنتیجه آن تفکیک دو قطبش مختلف، بر اساس تفاوت رفتار فرکانسی دو بازوی MZI محقق می­گردد. با در نظر گرفتن طول‌موج مرکزی nm1550، ساختار به­گونه­ای طراحی شده است که بهترین عملکرد را در محدوده طول­موج nm1500 تا nm1600 داشته باشد. نتایج به‌دست‌آمده، تلفات عبور کمتر از 0.8 dB، نسبت ­تفکیک­ قطبش بیشتر از dB15، برای قطبش میدان الکتریکی و نسبت­ تفکیک ­­قطبش بیشتر از dB10 را برای قطبش میدان مغناطیسی، در محدوده بسیار وسیع طول‌موج nm1500 تا nm1600 نشان می­دهد. ساختار طراحی‌شده در مقایسه با تفکیک‌کننده‌های قطبشِ مبتنی بر کوپلر جهتی پهنای­باند بسیار بیشتر و حساسیت کمتری نسبت به خطاهای ساخت دارد. به‌علاوه ابعاد کلی ساختار طراحی‌شده 260×3.86 است که نسبت به تفکیک‌کننده‌های قطبشِ مبتنی بر MZI دارای ابعاد کوچک‌تری است.}, keywords_fa = {تفکیک‌کننده قطبش,تداخل‌گر ماخ – زندر,تزویج‌گر تداخل چندمُد,سیلیکون – روی – عایق,نسبت تفکیک قطبش}, url = {https://tjee.tabrizu.ac.ir/article_9131.html}, eprint = {https://tjee.tabrizu.ac.ir/article_9131_7c3d8bfb4445d7e6dab1b7d4a5257d81.pdf} } @article { author = {Fallah, M. A.}, title = {Application of Geomagnetic Detection in Marine Surveillance}, journal = {TABRIZ JOURNAL OF ELECTRICAL ENGINEERING}, volume = {49}, number = {2}, pages = {747-752}, year = {2019}, publisher = {Faculty of Electrical & Computer Engineering}, issn = {2008-7799}, eissn = {2538-3051}, doi = {}, abstract = {Vessel traveling at sea causes hydrodynamic anomalies in sea water called Kelvin waves. Motion of conductive sea water due to Kelvin waves in natural Earth's magnetic field makes these waves visible using magnetic transducers. Geomagnetic anomaly induced by the motion of vessels may extend several kilometers and stay up long hours under certain conditions which consider this geomagnetic anomaly as a good candidate in marine surveillance. From remote sensing point of view in this work, we proposed a method for detecting vessel geomagnetic anomaly using an airborne magnetic sensor. Analytical formulations are derived and shown that physical properties of hydrodynamic Kelvin waves in shallow water are directly related to vessel parameters such as speed and traveling direction. Numerical simulations are used to demonstrate the applicability of our results. Vessel detection is performed in frequency domain. It is shown that the proposed detection method is noise robust and can be used to detect a vessel in a noisy ambient. Effect of vessel parameters such as velocity and traveling direction in frequency spectrum of received signal are investigated.}, keywords = {Geomagnetic anomaly,vessel,velocity,traveling direction,marine surveillance,shallow water,passive magnetic detector}, title_fa = {کاربرد آشکارسازی غیرفعال ژئومغناطیسی در مراقبت دریایی}, abstract_fa = {حرکت شناور در آب دریا باعث ایجاد تغییرات هیدرودینامیکی می‌شود که به امواج کلوین معروف‌اند. از سوی دیگر، آب دریا به‌طور طبیعی دارای رسانایی الکتریکی ضعیفی است. حرکت آب دریا به‌عنوان یک رسانا در میدان مغناطیسی زمین باعث القاء یک میدان الکترومغناطیسی ضعیف شده که آن را بی‌­هنجاری ژئومغناطیسی گویند. امواج این میدان الکترومغناطیسی قادرند در شرایط خاص تا چندین کیلومتر و تا ساعت‌ها، همچنان به بقاء خود ادامه دهند که امکان مناسبی را جهت کشف حضور شناور توسط آشکارسازهای غیرفعال مغناطیسی ایجاد می‌کنند. بر این اساس، روش آشکارسازی بی‌­هنجاری ژئومغناطیسی شناور توسط یک حس‌گر هوابرد، پیشنهاد شده است. معادلات ریاضی حاکم بر بی­هنجاری ژئومغناطیسی در دریای با عمق محدود، رابطه این بی­هنجاری با پارامترهای شناور نظیر سرعت و جهت حرکت را نشان می‌دهد. کاربردی­بودن ایده پیشنهادی توسط شبیه‌سازی نشان داده‌ شده و آشکارسازی شناور در حوزه فرکانس انجام ‌شده است. با انجام شبیه‌سازی در حضور نویز محیطی نشان داده‌ شده که امکان آشکارسازی شناور توسط طیف فرکانسی سیگنال دریافت­شده از حس‌گر هوابرد وجود دارد و تأثیر پارامترهای فیزیکی شناور در تغییر طیف فرکانسی به‌خوبی مشهود است.}, keywords_fa = {بی‌‌هنجاری ژئومغناطیسی,شناور,سرعت,جهت حرکت,مراقبت دریایی,کم‌عمق,آشکارساز غیرفعال مغناطیسی}, url = {https://tjee.tabrizu.ac.ir/article_9148.html}, eprint = {https://tjee.tabrizu.ac.ir/article_9148_738f4ce4644d8d84f8ec99a420d6e7b7.pdf} } @article { author = {Firouzmakan, P. and Hooshmand, R. and Khodabakhshian, A. and Bornapour, M.}, title = {Simultaneous Energy Management of Micro-CHP Units and Storage Systems in Microgrids Considering Responsive Loads}, journal = {TABRIZ JOURNAL OF ELECTRICAL ENGINEERING}, volume = {49}, number = {2}, pages = {753-765}, year = {2019}, publisher = {Faculty of Electrical & Computer Engineering}, issn = {2008-7799}, eissn = {2538-3051}, doi = {}, abstract = {A suitable energy management system (EMS) is an essential tool for optimal operation of a Microgrid with different resources considering uncertainties. In this paper, a day-ahead stochastic EMS is proposed in order to minimize the cost operation and maximize the reliability of Microgrid. The proposed EMS should supply electrical and thermal loads of Microgrid. A stochastic framework based on scenario generation is used to response the uncertainties of electrical load, market price and renewable energy sources (RESs). Also demand response programs (DRPs) are provided based on various load shifting contracts to consumers. In addition, both islanding and grid-connected operations of Microgrid are handled. Capability of the proposed method is proved by simulation results of a 3-feeder Microgrid with 7 generation units.}, keywords = {microgrid,renewable energy sources (RESs),Micro-CHP,demand response (DR),reliability,stochastic programming}, title_fa = {مدیریت هم‌زمان انرژی منابع Micro-CHP و ذخیره‌سازهای انرژی در ریزشبکه‌ها با وجود بارهای پاسخگو}, abstract_fa = {پیاده‌سازی یک سیستم مدیریت انرژی مناسب جهت بهره‌برداری بهینه از منابع انرژی یک ریزشبکه با عدم‌قطعیت‌های موجود، از اهمیت زیادی برخوردار است. در این مقاله، یک سیستم مدیریت انرژی تصادفی با هدف کاهش هزینه و افزایش قابلیت اعتماد ریزشبکه، برای روز-پیشرو، ارائه شده‌است. سیستم مدیریت انرژی پیشنهادی، وظیفه تامین بار الکتریکی و حرارتی ریزشبکه را با هدف کاهش هزینه بهره‌برداری و افزایش قابلیت‌اعتماد برعهده دارد. در این روش از یک چهارچوب تصادفی مبتنی بر تولید سناریو جهت پوشش عدم‌قطعیت‌های موجود در بازار برق، بار الکتریکی و تولیدهای تجدیدپذیر، استفاده شده‌است. همچنین، برنامه‌های پاسخ تقاضا در قالب قراردادهای انتقال بار از سوی بهره‌بردار ریزشبکه به مصرف‌کنندگان، ارائه می‌شود. علاوه‌برآن، بهره‌برداری از ریزشبکه در دو حالت اتصال به شبکه بالادست و جزیره‌ای، مدنظر قرار می‌گیرد. با تحلیل نتایج به‌دست‌آمده از شبیه‌سازی یک ریزشبکه با سه فیدر و هفت واحد تولیدی، قابلیت روش پیشنهادی موردارزیابی قرار می‌گیرد.}, keywords_fa = {ریزشبکه,تولیدهای تجدیدپذیر,Micro-CHP,پاسخ تقاضا,قابلیت اعتماد,برنامه‌ریزی تصادفی}, url = {https://tjee.tabrizu.ac.ir/article_8827.html}, eprint = {https://tjee.tabrizu.ac.ir/article_8827_9c279645c6a1ed99ef0d50f8f446f0b5.pdf} } @article { author = {Feizi, T. and Moattar, M. H.}, title = {A Novel Intrusion Detection System Based on Support Vector Machine and Improved Artificial Bee Colony Optimization}, journal = {TABRIZ JOURNAL OF ELECTRICAL ENGINEERING}, volume = {49}, number = {2}, pages = {767-782}, year = {2019}, publisher = {Faculty of Electrical & Computer Engineering}, issn = {2008-7799}, eissn = {2538-3051}, doi = {}, abstract = {Intrusion in the network is increasing. Intrusion detection system can greatly prevent network attacks. Feature selection is a critical issue in intrusion detection systems which have a considerable impact on the accuracy and effectiveness of the system. In this study, a new hybrid network intrusion detection system with improved artificial bee colony algorithm using support vector machine classifier is proposed for feature selection. The main idea is utilizing a combination of search equations of particle swarm optimization and Differential Evolution for updating bee’s position of employed and onlooker bees and utilizing levy flight on scout bees phase, to improve exploitation and increase the convergence rate of the standard artificial bee colony algorithm. The robustness and stability of the proposed approach is evaluated on NSL-KDD dataset and showed significant improvement on the overall performance of intrusion detection system with an accuracy of 98.97 percent.}, keywords = {Intrusion Detection System,Artificial Bee Colony Algorithm,Support Vector Machine,Evolutionary Optimization,Levy Flight}, title_fa = {ارائه یک سیستم تشخیص نفوذ جدید مبتنی بر ماشین بردار پشتیبان و بهینه‌سازی کلونی زنبور مصنوعی بهبودیافته}, abstract_fa = {میزان نفوذ در شبکه در حال افزایش است. سیستم تشخیص نفوذ، می‌تواند تا حد زیادی از حملات به شبکه جلوگیری کند. انتخاب ویژگی یک موضوع حیاتی در سیستم‌های تشخیص نفوذ می‌باشد که بر روی صحت و کارایی آن تأثیر بسزایی دارد. در این تحقیق، یک سیستمِ تشخیصِ نفوذ در شبکهِ ترکیبیِ جدید با استفاده از الگوریتم کلونی زنبور مصنوعی بهبودیافته مبتنی بر طبقه‌بند ماشین بردار پشتیبان با روش ارزیابی 10-fold برای انتخاب بهترین ویژگی‌ها پیشنهاد گردیده است. ایده اصلی، از ترکیب معادلات جستجوی بهینه‌سازی ازدحام ذرات و تکاملی تفاضلی در فاز زنبورهای کارگر و ناظر به‌منظور به‌روزرسانی موقعیت زنبورها و به‌کارگیری پرواز لوی در فاز زنبورهای پیشاهنگ، به‌منظور بهبود بهره‌برداری و نرخ همگرایی در الگوریتم کلونی زنبور مصنوعی می‌باشد. روش پیشنهادی مقاومت و پایداری خود را بر روی مجموعه‌داده NSL-KDD نشان داده و به‌طور قابل توجهی توانسته به بهبود عملکرد کلی سیستم تشخیص نفوذ با صحت 98/97 درصد کمک کند.}, keywords_fa = {سیستم تشخیص نفوذ,الگوریتم کلونی زنبور مصنوعی,ماشین بردار پشتیبان,بهینه‌سازی تکاملی,پرواز لوی}, url = {https://tjee.tabrizu.ac.ir/article_9134.html}, eprint = {https://tjee.tabrizu.ac.ir/article_9134_d73e0e946f1af71912eefad8b2c3e8be.pdf} } @article { author = {Ghorbaninejad, H. and Ettehad Mohkam, O.}, title = {Design, analysis and simulation of a microstrip filtenna using pass band filter synthesis approach}, journal = {TABRIZ JOURNAL OF ELECTRICAL ENGINEERING}, volume = {49}, number = {2}, pages = {783-791}, year = {2019}, publisher = {Faculty of Electrical & Computer Engineering}, issn = {2008-7799}, eissn = {2538-3051}, doi = {}, abstract = {In this paper, the simulation, analysis and design of a filtering antenna (filtenna) has been presented. A rectangular microstrip antenna and a parallel-coupled half-wavelength resonator filter are combined together to design a filtenna. This structure has a substrate with dielectric constant of 2.6. The proposed structure form a forth order band-pass filter with Chebyshev response and center frequency of 2.45 GHz. First, a parallel-coupled half-wavelength resonator filter was designed using Filter Synthesis Approach, then a microstrip rectangular patch was used instead of the last resonator of filter to act not only as the last resonator of filter, but also as a radiating element. The 3-dB bandwidth of the structure is 260 MHz and the -10-dB bandwidth is equal to 10.5 percent. The proposed filtenna has a good out-of-band gain suppression, flat in-band gain, and well-shaped radiation pattern. The performance of the proposed filtenna has been simulated with HFSS.}, keywords = {antenna,Filter,Microstrip,filtenna,parallel-coupled,half-wavelength,resonator}, title_fa = {طراحی، تحلیل و شبیه‌سازی یک فیلتنای مایکرواستریپ با روی‌کرد طراحی فیلتر میان‌گذر}, abstract_fa = {طراحی، تحلیل و شبیه‌سازی یک آنتن با قابلیت فیلترینگ ارائه شده‌است. یک آنتن مایکرواستریپ مربعی و فیلتر مایکرواستریپ میان‌گذر با تشدیدکننده‌های نصف طول موج تزویج‌شده‌ی موازی، برای طراحی یک فیلتنا با یک‌دیگر ترکیب شده‌اند. زیرلایه این ساختار دارای ضریب دی‌الکتریک 2.6 است. اجزای این فیلتنا با یک‌دیگر یک فیلتر مرتبه‌ی 4 با پاسخ چبیشف را تشکیل می‌دهند که فرکانس مرکزی آن 2.45 گیگاهرتز است. ابتدا یک فیلتر میان‌گذر مایکرواستریپ با تشدیدکننده‌های نصف طول موج تزویج شده‌ی موازی، طراحی شد و سپس به‌جای تشدیدکننده‌ی آخر آن یک صفحه‌ی مایکرواستریپ مستطیلی قرار گرفت تا علاوه‌بر نقش تشدیدکننده‌ی آخر فیلتر، نقش یک عنصر تشعشع‌کننده را نیز ایفا کند. پهنای باند 3 دسیبل این ساختار 260 مگاهرتز و پهنای باند10- دسیبل آن برابر با 10.5 درصد است. فیلتنای پیشنهادی فرکانس‌های خارج از باند را به‌خوبی حذف می‌کند، در باند عبور بهره‌ی نسبتاً یک‌نواخت و الگوی تشعشعی مناسبی دارد. درستی عملکرد نمونه طراحی‌شده با نرم‌افزار شبیه‌سازی HFSS ارزیابی شده‌است.}, keywords_fa = {آنتن,فیلتر,مایکرواستریپ,فیلتنا,تزویج‌شده‌ی موازی,نصف-طول موج,تشدیدکننده}, url = {https://tjee.tabrizu.ac.ir/article_9120.html}, eprint = {https://tjee.tabrizu.ac.ir/article_9120_470b7a6489ebcf11b979c7eb55c94146.pdf} } @article { author = {Gholinezhad, J. and Shariatinasab, R. and Sheshyekani, K.}, title = {Time Domain Frequency Dependence Modeling of Grounding System in order to Study the Lightning Performance of Transmission Lines}, journal = {TABRIZ JOURNAL OF ELECTRICAL ENGINEERING}, volume = {49}, number = {2}, pages = {793-804}, year = {2019}, publisher = {Faculty of Electrical & Computer Engineering}, issn = {2008-7799}, eissn = {2538-3051}, doi = {}, abstract = {This paper presents a new method for proper modeling of time domain multi-ports grounding systems that can be implemented in transient state-of-the-art analysis software. The presented method aims in minimizing the approximation in the frequency modeling of grounding systems in the transient analysis of power systems. The proposed solution is divided into three stages: First, the use of an electromagnetic method for solving the Maxwell equations, which leads to the extraction of the impedance matrix of the grounding system in a desired frequency range. In the next step, a logical approximation of the impedance matrix was made using the Vector Fitting (VF) method. The used VF method has led to the fitting of a set of poles for all impedance matrix arrays. In the final stage, considering that all the transient soft wares analyze power systems based on the admittance matrix, the proper model of the time domain multi-ports grounding system is executed by state space equations. The proposed modeling is performed on a typical 132 kV transmission line, and performance of implemented grounding system is compared with the previous methods including admittance matrix modeling and conventional model based on simple linear resistances.}, keywords = {multiport grounding system,impedance modeling,vector fitting}, title_fa = {استخراج مدل وابسته به فرکانس سیستم زمین در حوزه زمان جهت تحلیل عمل‌کرد صاعقه در خطوط انتقال}, abstract_fa = {این مقاله یک روش جدید برای استخراج مدل مناسب حوزه زمان سیستم‌های زمین چنددرگاهه، که قابلیت پیاده‌سازی در نرم‌افزارهای تحلیل حالت گذرا را داشته‌باشند، ارائه می‌‌دهد. این روش کمک می‌کند تا با کم‌ترین تقریب، بتوان رفتار دقیق و وابسته به فرکانس سیستم زمین را در تحلیل گذرای سیستم‌های قدرت در نظر گرفت. راهکار ارائه‌شده در سه مرحله تقسیم‌بندی می‌شود: اول، به‌کارگیری روش الکترومغناطیسی ممان جهت حل معادلات ماکسول که منجربه استخراج ماتریس امپدانس سیستم زمین در رنج فرکانسی مطلوب می‌گردد. در مرحله بعد یک تقریب منطقی از ماتریس امپدانس سیستم زمین با استفاده از روش برازش برداری (VF) صورت می­گیرد. روش VF به­کاررفته، منجربه برازش مجموعه­ای از قطب‌ها برای همه‌ی المان‌های ماتریس امپدانس گردیده‌است. در مرحله آخر، با توجه به این‌که نرم­افزارهای حالت گذرا برمبنای ماتریس ادمیتانس به تحلیل سیستم‌های قدرت می‌پردازند؛ با تغییر متغیرهای مناسب، مدل مناسب سیستم زمین چنددرگاه در حوزه زمان که قابلیت پیاده‌سازی در نرم‌افزارهای حالت گذرا را داشته‌باشد، به‌صورت معادلات فضای حالت استخراج گردیده‌است. مدل‌سازی پیشنهادی برروی یک خط انتقال مرسوم 132 کیلوولت پیاده شده و عمل‌کرد سیسستم زمین با روش­های قبلی شامل مدل‌سازی برمبنای ماتریس ادمیتانس و حالت مرسوم استفاده از مقاومت خطی ساده مقایسه شده‌است.}, keywords_fa = {سیستم زمین چنددرگاهه,مدل‌سازی امپدانسی,برازش برداری}, url = {https://tjee.tabrizu.ac.ir/article_9147.html}, eprint = {https://tjee.tabrizu.ac.ir/article_9147_427ece35c327d424cbc443433e817940.pdf} } @article { author = {Kazeminia, S. and Mahdavi, S.}, title = {Offset Cancellation in a 800MS/s Single-Stage Comparator by Analog Trimming on the Body Voltage of PMOS Devices}, journal = {TABRIZ JOURNAL OF ELECTRICAL ENGINEERING}, volume = {49}, number = {2}, pages = {805-818}, year = {2019}, publisher = {Faculty of Electrical & Computer Engineering}, issn = {2008-7799}, eissn = {2538-3051}, doi = {}, abstract = {A novel methodology is proposed for offset cancellation in single-stage latched comparators at high comparison speeds. In contrast to the regular methods, high-gain op-amp is not required and the loop accuracy is enhanced by small variations on the body voltages of PMOS devices. Hence, the number of digital signals which are transferred to the analog section are reduced and digital coupling effects are considerably improved. A novel read-out circuit is also proposed which compensates the parasitic capacitance of the next cell and quadruples the fan-out of the comparator, consequently. Worst-Case simulation results confirms that the proposed comparator can detect 1.5mVolts input difference, at all process corners, in presence of 15mVolts input offset voltage, at 800MS/s comparison rate. The Monte-Carlo analysis for 100 iterations on input offset voltages shows that input referred offset would be improved to 150μV while was 25mVolts at 3σ before the correction. Power consumption is 0.55mW at 800MS/s comparison speed. Post-Layout simulation results are presented using the BSIM3v3 model of a 0.18μm CMOS technology.}, keywords = {Latched comparators,high-speed ADCs,offset cancelled comparators,single-stage comparators}, title_fa = {حذف آفست در مقایسه‌کننده تک‌طبقه با سرعت مقایسه 800 میلیون نمونه برثانیه با روش تغییر آنالوگ ولتاژ بدنه ترانزیستورهای PMOS}, abstract_fa = {دراین مقاله، ساختار متداول مقایسه‌کننده‌های تک‌طبقه به‌گونه‌ای اصلاح شده است که آفست ترانزیستورهای ورودی بدون استفاده از آپ‌امپ کمکی بهره‌بالا، با دقت بسیار خوبی جبران می‌شود. تغییر از فاز پیش-تقویت به فاز لچ، با دستور سیگنال‌های آنالوگ با دامنه کوچک، از طریق بدنه ترانزیستورهای PMOS در مسیر حلقه فیدبک مثبت و منفی میسر می‌شود؛ درنتیجه، تعداد سیگنال‌های دیجیتال که برای کنترل عملکرد مقایسه‌کننده به بخش آنالوگ منتقل می‌شوند، کاهش یافته و اثرات تزویجی سیگنال‌های دیجیتال در بخش آنالوگ لی‌اوت بهبود می‌یابد. مدار جدیدی برای افزایش قدرت درایو مقایسه‌کننده (تا چهار برابر معمول) ارائه شده است که با جبران بخش بزرگی از خازن مزاحم طبقات بعدی، امکان مقایسه در سرعت‌های بالاتر را نیز فراهم می‌کند. شبیه‌سازی‌های پس از لی‌اوت در شرایط سخت نشان می‌دهد که مقایسه‌کننده پیشنهادی می‌تواند اختلاف ولتاژ 1.5 میلی‌ولت را در تمام گوشه‌های پروسه و با حضور ولتاژ آفست ورودی 15 میلی‌ولت، در سرعت نمونه‌برداری 800 میلیون نمونه‌برثانیه، به‌درستی تشخیص دهد. آنالیز مونت‌کارلو در 100 تکرار مختلف، با انتخاب تصادفی ولتاژ آفست ورودی از توزیع گاوسین با مقدار 25 میلی ولت در 3σ نشان می‌دهد که انحراف معیار آفست ارجاع‌شده به ورودی به 150 میکروولت کاهش می‌یابد. کل توان‌مصرفی مقایسه‌کننده پیشنهادی 550 میکرووات در سرعت نمونه‌برداری 800 میلیون نمونه برثانیه است. نتایج شبیه‌سازی پس از لی‌اوت با استفاده از نرم‌افزار HSPICE و براساس نسخه BSIM3v3 در مدل‌سازی ترانزیستورهای پروسه 0.18 میکرون ارائه شده‌اند.}, keywords_fa = {مقایسه کننده,مبدل‌های آنالوگ به دیجیتال سرعت بالا,مقایسه‌کننده‌های بدون آفست,مقایسه‌کننده تک‌طبقه}, url = {https://tjee.tabrizu.ac.ir/article_9125.html}, eprint = {https://tjee.tabrizu.ac.ir/article_9125_a98f09ffd9397f97399c5839af92094b.pdf} } @article { author = {Kayvan Shokooh, R. and Okhovvat, M.}, title = {Efficient Masked Target Detection by Fast Adaptive Pulse Compression Algorithm with Flexible Filter Length}, journal = {TABRIZ JOURNAL OF ELECTRICAL ENGINEERING}, volume = {49}, number = {2}, pages = {819-831}, year = {2019}, publisher = {Faculty of Electrical & Computer Engineering}, issn = {2008-7799}, eissn = {2538-3051}, doi = {}, abstract = {In this paper, we investigate the detection of masked weak moving targets in the adjacent fast strong target by using FAPC algorithm. The matched filter of conventional pulse compression radars induces range sidelobes in surrounding a target with high SNR that could mask the smaller targets. The mismatch created in received signal by Doppler phase shift, degrades APC filter performance in side lobe suppression. In this paper, the FFL-FAPC algorithm is proposed to reduce the range side lobes using the RMMSE estimator in its post-processing method. In various scenarios, we will investigate the detection of masked targets in comparsion with previous methods. Simulation results show that the FFL-FAPC algorithm reduce significantly of computational cost, in addition to provides improved Doppler robustness. }, keywords = {Fast adaptive pulse compression,Reiterative Minimum Mean Square Error estimator,Doppler phase shift,detection,Matched filter}, title_fa = {آشکارسازی مؤثر اهداف پنهان‌شده به‌وسیله الگوریتم فشرده‌سازی پالس وفقی سریع با طول فیلتر منعطف}, abstract_fa = { در این مقاله آشکارسازی اهداف متحرک ضعیف پنهان‌شده در مجاورت اهداف قوی سریع را با استفاده از الگوریتم  FAPC  بررسی می­کنیم. فیلتر منطبقِ رادارهای فشرده‌سازی پالس متعارف در اطراف هدفی با نسبت سیگنال به نویز بزرگ، لوب‌های جانبی برد بزرگی تولید می­کند که می­تواند اهداف کوچک را پنهان نماید. عدم تطبیق ایجادشده در سیگنال دریافتی به‌واسطه جابه­جایی فازی دوپلر، عملکرد فیلتر APC  در کاهش سطح لوب‌های جانبی را تنزل می­دهد. در این مقاله الگوریتم FFL-FAPC  پیشنهادشده است که برای کاهش لوب‌های جانبی برد از تخمین­گر RMMSE  به روش پساپردازش استفاده می­کند. در سناریوهای مختلف آشکارسازی اهداف پنهان‌شده را در مقایسه با روش­های قبلی، بررسی می­کنیم. نتایج شبیه‌سازی نشان می­دهد که الگوریتم FFL-FAPC علاوه بر کاهش قابل‌ملاحظه هزینه محاسبات، مقاومت دوپلر را هم بهبود می­بخشد. }, keywords_fa = {فشرده‌سازی پالس وفقی سریع,تخمین‌گر حداقل مجذور مربعات خطا تکراری,جابه‌جایی فازی دوپلر,آشکارسازی,فیلتر منطبق}, url = {https://tjee.tabrizu.ac.ir/article_9105.html}, eprint = {https://tjee.tabrizu.ac.ir/article_9105_078e0f9fad143108d5394ffdae13ffd7.pdf} } @article { author = {Mohebbi Najm Abad, J. and Soleimani, A.}, title = {Dynamic Thermal Management by Controlling CPU Frequency and Fan Speed}, journal = {TABRIZ JOURNAL OF ELECTRICAL ENGINEERING}, volume = {49}, number = {2}, pages = {833-845}, year = {2019}, publisher = {Faculty of Electrical & Computer Engineering}, issn = {2008-7799}, eissn = {2538-3051}, doi = {}, abstract = {Microprocessor designers use the design of multicore systems on a chip to increase their computing power. Adding the number of cores leads to an increase in the power density, followed by enhancement of temperature. Reactive and proactive approaches are two sets of the methods for managing the temperature. Unlike the reactive methods that act based on threshold temperature, proactive approaches utilize a thermal prediction model in thermal management. In this paper, two multilayer perceptron neural networks has been used for thermal prediction and temperature control. An appropriate dataset is provided for training each model. This dataset consists of some features that are read by sensors and measurement tools and new features that are produced by proposed processes. In this regard, historical features are suggested for thermal model. Proper features of thermal model are selected by using feature selection based on mutual information. The temperature is controlled by setting the processor frequency and fan speed. The features of control model are selected by non-dominated sorting genetic algorithm. The error of thermal model for different time distances is about 0.5 °C. The thermal control model has respectively 2% and 0.6% errors in determining the processor frequency and fan speed.}, keywords = {Dynamic thermal management,thermal prediction,feature selection,multilayer perceptron,temperature control}, title_fa = {مدیریت دمای پویا برای سیستم‌های چندهسته‌ای با کنترل فرکانس پردازنده و سرعت فن}, abstract_fa = {طراحان ریزپردازنده‌ها از طراحی سیستم‌های چندهسته‌ای بر روی یک تراشه برای افزایش توان محاسباتی آن‌ها بهره می‌برند. افزودن تعداد هسته‌ها، افزایش چگالی توان مصرفی و در پی آن افزایش دما را به‌دنبال دارد. برای کنترل و مدیریت دما، روش‌های واکنشی و فعال معرفی شده‌اند. برخلاف روش‌های واکنشی که بر اساس آستانه گذاری عمل می‌کنند، روش‌های فعال با بهره‌گیری از یک مدل پیش‌بینی دما، مدیریت دما را انجام می‌دهند. در این مقاله برای مدیریت دما، مدلی برای پیش‌بینی دمای آینده و مدلی برای کنترل دما پیشنهاد شده و از دو شبکه عصبی پرسپترون چندلایه‌ای برای تحقق آن‌ها استفاده شده است. برای آموزش هر یک از مدل‌ها، مجموعه داده مناسب فراهم شده است. در این مجموعه داده تعدادی از ویژگی‌ها با استفاده از حسگرها و سنجه‌های سیستم و دیگر ویژگی‌ها با پردازش‌های پیشنهادی فراهم شده‌اند. در این راستا، برای پیش‌بینی دما، ویژگی‌های سابقه‌ای پیشنهاد شده‌اند. ویژگی‌های مناسب برای پیش‌بینی دما، با روش انتخاب ویژگی بر پایه اطلاعات متقابل و ویژگی‌های مناسب برای مدل کنترلی با بهره‌گیری از الگوریتم ژنتیک مبتنی بر رتبه‌بندی نامغلوب، انتخاب شده‌اند. نتایج نشان می‌دهند خطای مدل پیش‌بینی برای فاصله‌های مختلف زمانی حدود 0.5 درجه سانتی‌گراد است و خطای مدل کنترل دما، در تعیین مقدار فرکانس پردازنده و سرعت فن، به‌ترتیب 2 و 0.6 درصد است.}, keywords_fa = {مدیریت دمای پویا,پیش‌بینی دما,انتخاب ویژگی,پرسپترون چندلایه‌ای,کنترل دما}, url = {https://tjee.tabrizu.ac.ir/article_8881.html}, eprint = {https://tjee.tabrizu.ac.ir/article_8881_f9fbac3bcae4b03edb61af8f738b1c6f.pdf} } @article { author = {Mohassel Feghhi, M.}, title = {Joint Time and Frequency Synchronization in Communication Systems Based on IEEE 802.11 Standard}, journal = {TABRIZ JOURNAL OF ELECTRICAL ENGINEERING}, volume = {49}, number = {2}, pages = {847-858}, year = {2019}, publisher = {Faculty of Electrical & Computer Engineering}, issn = {2008-7799}, eissn = {2538-3051}, doi = {}, abstract = {The growing demand for high-quality services together with the rapid increase in number of users have made the high data rate as one of the basic requirements of the next generation broadband wireless networks. One of the proposed solutions for this purpose is the Orthogonal Frequency Division Multiplexing (OFDM), which is used in various standards, such as IEEE 802.11. On the other hand, OFDM System’s performance is highly affected by carrier frequency offset and time offset. Therefore, one of the essential requirements of each OFDM receiver is its capability in performing accurate time and frequency synchronization. Hence, in this paper, a joint time and frequency synchronization method for communication systems based on IEEE 802.11 is proposed. As the IEEE 802.11 standard uses training sequence or preamble in its frame, synchronization methods employed in this standard should be based on using such training sequences. Then, based on different metrics and using computer simulations, the performance behavior of the proposed method in AWGN and multipath fading channels is evaluated and compared with various training-based synchronization methods. Simulation results verify desirable performance of the proposed method in practical scenarios.}, keywords = {Carrier frequency offset,training sequence,symbol timing estimation,pilot-based synchronization}, title_fa = {همگام‌سازی توأم زمانی و فرکانسی در سیستم‌های مخابراتی بر پایه استاندارد IEEE 802.11}, abstract_fa = {افزایش روزافزون تقاضا برای سرویس‌های باکیفیت با افزایش تعداد کاربران سبب شده‌است تا فراهم‌آوردن نرخ‌های بالای داده یکی از الزامات اساسی نسل آتی شبکه‌های بی‌سیم پهن‌باند گردد. یکی از راه‌کارهای پیشنهادشده برای این هدف بهره‌گیری از مدولاسیون OFDM است که در استانداردهای مختلفی هم‌چونIEEE 802.11  مورد استفاده قرار گرفته است. ازسوی‌دیگر عملکرد سیستم‌های مبتنی‌بر OFDM به‌شدت از آفست فرکانس حامل و نیز آفست زمان سمبل تأثیر می‌پذیرد. درنتیجه یکی از ملزومات اساسی هر گیرنده OFDM توانایی هم‌زمان‌سازی زمانی و فرکانسی با دقت بالا است. براین‌اساس، در این مقاله یک روش هم‌زمان‌سازی توأم زمانی و فرکانسی با دقت بالا برای به‌کارگیری در سیستم‌های مخابراتی مبتنی‌بر استاندارد IEEE 802.11  پیشنهاد می‌شود. باتوجه‌به وجود داده‌های آموزشی در این استاندارد، الگوریتم پیشنهادی می‌بایست برمبنای استفاده از این داده‌ها باشد. سپس بر پایه معیارهای مختلف، عملکرد روش پیشنهادی با استفاده از شبیه‌سازی‌های کامپیوتری در کانال نویز گوسی و نیز کانال محوشدگی چندمسیره مورد سنجش قرار می‌گیرد و با روش‌های مختلف هم‌زمان‌سازی بر پایه داده آموزشی معرفی‌شده در مراجع، مقایسه می‌گردد. نتایج شبیه‌سازی مؤید عملکرد مطلوب و کاربردی‌بودن روش پیشنهادی است.}, keywords_fa = {آفست فرکانس حامل,دنباله آموزشی,تخمین ابتدای سمبل,همگام‌سازی بر پایه پایلوت}, url = {https://tjee.tabrizu.ac.ir/article_8912.html}, eprint = {https://tjee.tabrizu.ac.ir/article_8912_cda2f75fab73ed3629cb235d0ccfe8af.pdf} } @article { author = {Mohammadi, P. and Banihashem, A.}, title = {Diplexer Embedded with Crisped S-shaped Complementary Split Ring Resonators for LTE Band Application}, journal = {TABRIZ JOURNAL OF ELECTRICAL ENGINEERING}, volume = {49}, number = {2}, pages = {859-864}, year = {2019}, publisher = {Faculty of Electrical & Computer Engineering}, issn = {2008-7799}, eissn = {2538-3051}, doi = {}, abstract = {In this paper, a novel structure of diplexer is designed based on Substrate Integrated Wave guide (SIW) technology and S-shaped complementary split ring resonator  to operate in LTE1.3 GHz  -2.1 GHz band. A miniaturized and compact SIW diplexer implemented by Crisped S-shaped Complementary Split Ring operated in a waveguide format is proposed and presented. In design process, firstly, the filters corresponding to each of the bands is designed in simulator, then by using S-parameter of each filter the T-shaped structure dimensions of the input feeding diplexer is achieved and optimized. It is deduced from measurement results of diplexer that input and output impedance matching in the respective bands, transmission losses are1dB and 2dB for 1.3 GHz and 2.1 GHz respectively. The isolation between output ports is better than 30dB. Finally the proposed structure reflects the performance is highly desirable. This structure illustrates advantages in terms of the small size, low loss, high isolation, easy realization and integration with other planar circuits. }, keywords = {diplexer,Microstrip,SIW,complementary split ring resonator}, title_fa = {دیپلکسر با رزوناتورهای حلقوی مکمل شکاف‌دار به شکلS خم‌شده در کاربردهای LTE}, abstract_fa = {در این مقاله ساختار جدیدی از یک دیپلکسر با استفاده از تکنولوژی موجبرمجتمع‌شده (SIW) و رزوناتور حلقوی مکمل شکاف‌دار برای کاربردهای  LTE در فرکانس های 1.3 گیگاهرتز و2.1 گیگاهرتز طراحی شده است. این دیپلکسر فشرده‌شده, توسط رزوناتور حلقوی S شکل در یک ساختار موجبری ارائه شده است. در این طرح ابتدا فیلترهای متناظر با هریک از باندها در شبیه‌ساز طراحی و سپس با استفاده از پارامترهای پراکندگی هر یک از فیلترها ساختار T شکل در ورودی دیپلکسر بهینه‌سازی شد. با توجه به نتایج اندازه‌گیری دیپلکسر ساخته‌شده دهانه‌های ورودی و خروجی تطبیق امپدانسی مناسبی در باندهای مورد نظر دارند و تلفات انتقالی در فرکانس های1.3 گیگاهرتز و2.1  گیگاهرتز به‌ترتیب حدود  1 دسی‌بل و 2 دسی‌بل است. مقدار ایزولاسیون بین دهانه‌های خروجی بیش از30 دسی‌بل است. نهایتا ساختار پیشنهادی کارایی بسیار مطلوبی را منعکس می‌کند. این ساختار مزیت‌هایی را مانند ابعاد کوچک ، تلفات پایین ، ایزولاسیون بالا ، ساخت آسان و قابلیت مجتمع‌سازی‌شدن با دیگر مدارات مسطح را دارد.}, keywords_fa = {دیپلکسر,ریزنوار,موج‌بر مجتمع‌شده,رزوناتورهای حلقوی مکمل}, url = {https://tjee.tabrizu.ac.ir/article_9112.html}, eprint = {https://tjee.tabrizu.ac.ir/article_9112_f7da3e0d1aca5a0d8cba42fd055e7efc.pdf} } @article { author = {Maleki, M. and Mohseni Armaki, S. H. and Hamidi, E.}, title = {Presentation of an Applicable Method for Characterization of Electromagnetic Parameters of Ferrite Materials at Ku Band}, journal = {TABRIZ JOURNAL OF ELECTRICAL ENGINEERING}, volume = {49}, number = {2}, pages = {865-872}, year = {2019}, publisher = {Faculty of Electrical & Computer Engineering}, issn = {2008-7799}, eissn = {2538-3051}, doi = {}, abstract = {Since validation of the electromagnetic parameters of manufactured or purchesed ferrite materials is the first step in designing and implementation of the diffrent ferrite-based devices in communication systems, ferrite characterization is verry important. in this paper an algorithm is simulated and implemented which is based on the minimization of an objective function. the objective function's parameters are the reflection and transmission coefficients of the ferrite in a rectangular wave guide.in compairsion with other works proposed method only needs to the amplitude of the reflection and transmission coefficients to estimate the parameters of ferrite materials. This makes the implementation easy and eliminates the problems associated with phase calibration and sensitivity. The proposed method is simulated for a nickel ferrite and experimentally tested on SL-470 ferrite sample and the results have been compared with the manufacturer's catalog.}, keywords = {ferrite,electromagnetic parameters,the reflection and transmission coefficients,mode matching analysis}, title_fa = {ارائه یک روش کاربردی برای شناسایی پارامترهای الکترومغناطیسی مواد فریتی در باند Ku}, abstract_fa = { اولین قدم در طراحی و ساخت ادوات مختلف در سیستم‌های مخابراتی در اختیارداشتن اطلاعات مربوط به پارامترهای الکترومغناطیسی مواد مورد استفاده می‌باشد. در بین مواد مختلف فریت‌ها دارای جایگاه خاصی می‌باشند. در نتیجه شناسایی ماده فریتی دارای اهمیت بسزایی می‌باشد. در این مقاله یک روش کاربردی ساده برای شناسایی مواد فریتی ارائه شده است. این روش بر اساس کمینه‌کردن خطای یک تابع هدف می‌باشد. پارامترهای این تابع ضرایب عبور و ضرایب انعکاسماده فریتی در یک موج‌بر مستطیلی هستند که شامل اطلاعات اندازه‌گیری شده از نمونه و نیز اطلاعات تحلیل نظری نمونه به روش تطبیق‌مود هستند. از آن‌جایی که روش پیاده سازی‌شده تنها به دامنه ضرایب عبور و انعکاس نمونه نیاز دارد، در مقایسه با سایر روش‌های موجود مشکلات کالیبراسیون فاز و حساسیت شدید به آن را ندارد و می‌تواند روشی کارامد برای شناسایی مواد فریت با امکانات داخل کشور باشد و نیاز به تجهیزات گران‌قیمت و یا ارسال نمونه به خارج از کشور را برطرف نماید. روش پیشنهادی برای یک فریت نیکلی شبیه‌سازی شده و به‌صورت تجربی روی نمونه فریت SL-470 آزمایش شده‌است و نتایج با اطلاعات ارائه‌شده درکاتالوگ سازنده مقایسه شده‌است.}, keywords_fa = {فریت,پارامترهای الکترومغناطیسی,ضرایب انعکاس و عبور,آنالیز تطبیق مود}, url = {https://tjee.tabrizu.ac.ir/article_9102.html}, eprint = {https://tjee.tabrizu.ac.ir/article_9102_c7f64ea341e380ec9e8d473982ddd123.pdf} } @article { author = {Moloudian, G. and Bahrami, S. and Ghouhestani, H.}, title = {Design and fabrication of a dual-band band-pass filter using dual-mode square patch resonator and ring-shaped slot}, journal = {TABRIZ JOURNAL OF ELECTRICAL ENGINEERING}, volume = {49}, number = {2}, pages = {873-879}, year = {2019}, publisher = {Faculty of Electrical & Computer Engineering}, issn = {2008-7799}, eissn = {2538-3051}, doi = {}, abstract = {In this paper, a band-pass filter with suitable performance for wireless telecommunication applications is designed and fabricated. For designing the proposed filter, the dimensions of dual-mode square patch resonator are chosen to be within a quarter of the wavelength. Circular perturbations (circular slots) are used for better performance of the proposed filter. A dual channel filter is designed and fabricated on an FR4 substrate. The center frequency of the proposed filter for the first channel is equal to 2.35 GHz and for the second channel is equal to 3.375 GHz; the 3-dB fractional bandwidths (FBWs) of 12.75 and 10.3 %, respectively. The measured insertion losses are 0.8 and 1.45 dB, respectively. The proposed filter has a small size of 20 mm×  20mm. The group delay of the proposed filter for the first and second pass bands is almost constant, which indicates phase of the insertion loss in the pass bands is linear. The proposed filter is fabricated and tested. The results of simulation are fairly consistent with that of the measurement. The proposed filter can be used in wireless communications and modern microwave telecommunication.}, keywords = {Band-pass filter,Microstrip,dual-mode patch square,circular slot}, title_fa = {طراحی و ساخت فیلتر میان‌گذر مایکرواستریپ دو باند با استفاده از رزوناتور پچ مربعی دو مُدی و شکاف‌های دایروی شکل}, abstract_fa = {در این مقاله، به طراحی و ساخت یک فیلتر میان‌گذر با عملکرد مناسب برای استفاده در کاربردهای مخابرات بی‌سیم پرداخته شده است. برای طراحی فیلتر پیشنهادی، ابعاد رزوناتور پچ مربعی دو مُدی به‌اندازه ربع طول موج درنظر گرفته شده است. برای عملکرد بهتر فیلتر پیشنهادی از اختلالات دایروی (شکاف‌های دایروی) شکل استفاده شده است. فیلتر دو کاناله پیشنهادی بر روی زیرلایه FR4 طراحی و ساخته شده است. فرکانس مرکزی فیلتر پیشنهادی برای کانال اول برابر 35/2 گیگاهرتز و برای کانال دوم 3.375 گیگاهرتز با پهنای باند نسبی 12.75و 10.3 درصد  است. میزان تلفات عبوری برای باند عبور اول برابر0.8 دسی‌بل و برای باند عبور دوم 1.45 دسی‌بل است. اندازه فیلتر پیشنهادی کوچک و برابر  با 20 ×20 میلی‌متر مربع می‌باشد. تأخیر گروه فیلتر پیشنهادی برای باندهای عبور اول و دوم تقریباً ثابت است که این امر نشان دهنده این است که فاز تلفات عبوری در باند عبور خطی است. فیلتر پیشنهادی، پس از طراحی و شبیه‌سازی، بر روی زیرلایه موردنظر ساخته شده و در نهایت مورد تست و اندازه‌گیری قرار گرفته است.  نتایج شبیه‌سازی با نتایج اندازه‌گیری شده دارای تطابق بسیار خوبی می‌باشد. از فیلتر پیشنهادی می‌توان در ارتباطات بی‌سیم و مخابرات مایکروویو مدرن استفاده نمود.}, keywords_fa = {فیلتر میان‌گذر,مایکرواستریپ,پچ مربعی دو مُدی,شکاف دایروی شکل}, url = {https://tjee.tabrizu.ac.ir/article_8851.html}, eprint = {https://tjee.tabrizu.ac.ir/article_8851_1c958bc0729711e6d30ce81b94567bd3.pdf} } @article { author = {Momeni, H. and Taheri, M.A.}, title = {Correlation Analysis of Output Streams Jump Generators in Stream Ciphers}, journal = {TABRIZ JOURNAL OF ELECTRICAL ENGINEERING}, volume = {49}, number = {2}, pages = {881-887}, year = {2019}, publisher = {Faculty of Electrical & Computer Engineering}, issn = {2008-7799}, eissn = {2538-3051}, doi = {}, abstract = {One method of design the LFSR-based stream ciphers is using irregular clock that it is most famous structures. In recent years became a springboard technique called clock control that improves efficiency compared to generators has become tighter. In this way, instead of several clock has been changed and values, in the state through the middle. Per basic polynomials, a jump in the index jump is still there. It is clear that for the length of each LFSR, there are several initial polynomials that same period, but the size of the jump index is different. In this paper, by analyzing the correlation attack on generators springboard, it was concluded that the selection of index jump polynomials with maximum results in minimum correlation between output and input sequence is productive. So in the design of stream ciphers with a springboard generation structure, in terms of correlation attacks, the polynomial with most rate of jump up the index is priority.}, keywords = {Jump Generator,Jump Index,Correlation Attack,Stream Cipher,Shrink Generator}, title_fa = {تحلیل همبستگی دنباله خروجی مولدهای پرشی در رمزهای جریانی}, abstract_fa = {یکی از روش‌های طراحی رمزهای جریانی مبتنی بر LFSR­ ها، استفاده از روش کلاک نامنظم است که از معروف‌ترین ساختارهای آن، ساختار انقباضی است. در سال‌های اخیر روشی به نام کنترل کلاک پرشی مطرح شد که باعث بهبود کارایی در مقایسه با مولدهای انقباضی گشته است. در این روش به‌جای اینکه چندین کلاک زده شده و مقادیر تغییر یابند، درواقع از روی حالت‌های میانی عبور می‌شود. به‌ازای هر چندجمله‌ای اولیه، یک‌میزان پرش ثابت وجود دارد که شاخص پرش نام دارد. بدیهی است که به‌ازای طول هر LFSR، چندجمله‌ای‌های اولیه متعددی وجود دارد که دوره تناوب یکسان دارند، اما اندازه شاخص پرش آن‌ها متفاوت است. در این مقاله با تحلیل حمله همبستگی روی مولدهای پرشی، این نتیجه حاصل شد که انتخاب چندجمله‌ای با حداکثر شاخص پرش، موجب حداقل همبستگی بین دنباله خروجی و ورودی مولد می‌گردد. لذا در طراحی رمزهای جریانی با ساختار مولدهای پرشی، از دیدگاه حملات همبستگی، اولویت با انتخاب چندجمله‌ای‌هایی با حداکثر میزان شاخص پرش است.}, keywords_fa = {مولدهای پرشی,شاخص پرش,حمله همبستگی,مولدهای انقباضی,رمز جریانی}, url = {https://tjee.tabrizu.ac.ir/article_9104.html}, eprint = {https://tjee.tabrizu.ac.ir/article_9104_b8dee1567b1e0a672305168f17693080.pdf} } @article { author = {Mahdavi, M. S. and Gharehpetian, G. B. and Moaddabi, N.}, title = {Optimal presence of FACTS devices before fault occurrence for transient stability enhancement based on terminal voltage angle difference of the generators}, journal = {TABRIZ JOURNAL OF ELECTRICAL ENGINEERING}, volume = {49}, number = {2}, pages = {889-900}, year = {2019}, publisher = {Faculty of Electrical & Computer Engineering}, issn = {2008-7799}, eissn = {2538-3051}, doi = {}, abstract = {The ability of network generators to maintain their synchronism after a fault depends on several factors, including the initial conditions of the system before the fault, so it can be expected that by changing the system variables, such as the angle of the generator rotors in the system, the system stability can be against the fault. This change is possible by the Permanent presence of FACTS devices. The critical clearing time of fault as the most accurate criterion for transient stability evaluation can be the objective function of our optimization problem, but the determination of the critical clearing time, which involves the time domain simulation of the network along with the repeated examination of the fault occurrence It is time consuming to adjust the FACTS devices to a power system that is changing at any one time. In this paper, we present a new objective function based on the reduction of the voltage angle difference between generators terminals, which greatly increases the speed of optimization, in order to improve the transient stability of smart grid by setting up the online FACTS devices. Minimizing this objective function by optimizing the FACTS is equivalent to maximizing transient stability. In addition  to optimal tuning, optimal type, number and allocation of them are considered for long term. in determining the optimal number of these devices, the cost of investment is also considered.}, keywords = {Transient Stability,Critical Clearing Time,Voltage Angle Difference Between Generators Terminals,FACTS,PSO}, title_fa = {حضور بهینه‌ی ادوات FACTS پیش از وقوع خطا جهت بهبود پایداری گذرای سیستم قدرت بر اساس اختلاف زاویه ولتاژ ترمینال ژنراتورها}, abstract_fa = {حفظ پایداری گذرای سیستم قدرت بستگی به عوامل مختلفی از جمله شرایط اولیه‌ی سیستم قبل از وقوع خطا دارد، لذا می‌توان انتظار داشت که با تغییر متغیرهای سیستم مانند زاویه‌ی روتور ژنراتورها در حالت ماندگار سیستم بتوان پایداری شبکه در برابر خطا را افزایش داد، این تغییر با حضور دائم ادوات FACTS  و تنظیم بهینه آن‌ها به صورت آنلاین امکان‌پذیر است. زمان بحرانی رفع خطا به عنوان دقیق‌ترین معیار ارزیابی پایداری گذرا خود می‌تواند تابع هدف این مسئله‌ی بهینه‌سازی باشد، ولی تعیین زمان بحرانی رفع خطا که مستلزم شبیه‌سازی حوزه‌ی زمان شبکه ضمن بررسی وقوع مکرر خطا می‌باشد امری زمان‌بر است و برای تنظیم آنلاین ادوات FACTS در یک سیستم قدرت که در هر لحظه متغیرهایش در حال تغییر هستند مناسب نیست. در این مقاله جهت بهبود پایداری گذرای یک شبکه‌ی هوشمند از طریق تنظیم آنلاین ادوات FACTS تابع هدف جدیدی بر اساس کاهش اختلاف زاویه‌ی ولتاژ ترمینال ژنراتورها ارائه می‌شود که سرعت بهینه سازی را به طرز چشمگیری افزایش می‌دهد. کمینه ساختن این تابع هدف با به کارگیری بهینه ادوات FACTS، معادل بیشینه ساختن پایداری گذرا خواهد بود. علاوه بر تنظیمات ادوات FACTS نوع، تعداد و مکان بهینه آنها نیز لحاظ می‌شود و در تعیین تعداد این ادوات هزینه‌ی سرمایه گذاری نیز لحاظ می‌شود.}, keywords_fa = {پایداری گذرا,زمان بحرانی رفع خطا,اختلاف زاویه ولتاژ ژنراتورها,ادوات FACTS,الگوریتم بهینه سازی اجتماع ذرات}, url = {https://tjee.tabrizu.ac.ir/article_9133.html}, eprint = {https://tjee.tabrizu.ac.ir/article_9133_9d2c3802dbec44d81ab38f98e2d8e1a9.pdf} } @article { author = {Mivehchy, M. and Keshavarz, H.}, title = {Improved Processing and Increasing the Accuracy of Range Extraction in a FM/CW radar}, journal = {TABRIZ JOURNAL OF ELECTRICAL ENGINEERING}, volume = {49}, number = {2}, pages = {901-911}, year = {2019}, publisher = {Faculty of Electrical & Computer Engineering}, issn = {2008-7799}, eissn = {2538-3051}, doi = {}, abstract = {The low altitude primary search radar use a continuous wave, and in its simplest case, a sawtooth modulation is used in one scan and no modulation in the next one. By determining the frequency of the returning signal in two consecutive scans, the target range and radial velocity are extracted. In this method, the two successive scans are needed to determine the range and this is one of the main problems of this method. In order to simultaneously extract the radial velocity and the range, the modulating waveform is changed to a triangular wave form, and simultaneously two preprocesses are proposed to compensate for the spectral spreading by sampling and smoothing the returning signal. This has a significant effect in determining the exact components of the target in the low signal-to-noise conditions. Also, a simple algorithm is proposed to determine the coupled frequency components of the target in the pre-processed spectrum more accurately. The processing was done by using a TMS320C6416 DSP processor on an actual radar signal. The experimental results show a higher stability and less error in determining the range compared to other methods.}, keywords = {Sawtooth modulation,Triangular modulation,Spread distribution,Preprocessing,Smoothing spectrum,Range extraction}, title_fa = {بهبود پردازش و افزایش دقت استخراج برد در یک رادار FM/CW}, abstract_fa = {رادارهای اولیه جستجوگر ارتفاع پست از نوع موج پیوسته بوده و در ساده‌ترین حالت از مدولاسیون دندانه‌اره‌ای در یک اسکن و بدون مدولاسیون در اسکن بعدی استفاده می‌شده است. با تعیین فرکانس سیگنال بازگشتی در دو اسکن متوالی، برد و سرعت شعاعی هدف می‌تواند استخراج شود. لزوم دو اسکن متوالی برای تعیین برد از مشکلات اصلی این روش است. به‌منظور استخراج همزمان برد و سرعت شعاعی در طی یک‌بار رؤیت هدف، شکل موج مدوله‌کننده به مثلثی تغییریافته و همزمان به‌منظور جبران پخش‌شدگی طیف در اثر نمونه‌برداری و همچنین برای هموار نمودن طیف سیگنال بازگشتی، دو پیش‌پردازش ارائه‌شده است؛ که در تعیین دقیق‌تر مؤلفه‌های ناشی از هدف در شرایط سیگنال به نویز کوچک، تأثیر به سزایی دارد. هم‌چنین به‌منظور تعیین دقیق‌تر زوج مؤلفه‌های فرکانسی ناشی از هدف در طیف پیش‌پردازش شده، الگوریتمی ساده پیشنهادشده است. پردازش‌های موردنظر با استفاده از پردازنده DSP از نوع TMS320C6416 روی سیگنال واقعی رادار انجام‌گرفته است. نتایج تجربی حاصله نشان‌دهنده ثبات بیشتر و خطا کمتر در تعیین برد نسبت به روش‌های مورداستفاده پیشین، است}, keywords_fa = {مدولاسیون دندانه‌اره‌ای,مدولاسیون مثلثی,پخش‌شدگی طیف,پیش‌پردازش,هموار نمودن طیف,استخراج برد}, url = {https://tjee.tabrizu.ac.ir/article_9132.html}, eprint = {https://tjee.tabrizu.ac.ir/article_9132_68496277b4495f45f2d18500d049b0cd.pdf} } @article { author = {Naghavi, S. and Abrishamifar, A.}, title = {A Novel Analog Switch for High Precision Switched-Capacitor Applications}, journal = {TABRIZ JOURNAL OF ELECTRICAL ENGINEERING}, volume = {49}, number = {2}, pages = {913-923}, year = {2019}, publisher = {Faculty of Electrical & Computer Engineering}, issn = {2008-7799}, eissn = {2538-3051}, doi = {}, abstract = {The performance of a switched capacitor circuit strongly depends on its analog switches. This paper introduces a new technique to design a high precision analog MOS switch for switched-capacitor applications. To satisfy the accuracy requirements of the switch, a novel technique is proposed to minimize the charge injection and clock feed-through errors by using a very simple structure. Moreover, an innovative approach to increase the off-resistance of the switch and consequently minimizing its leakage current is presented. In order to evaluate the performance of the proposed switch, simulations are done in a 18μm standard CMOS technology. The on-resistance of the proposed switch is less than 560Ω over entire input signal range which completely satisfies the tracking bandwidth requirements. In addition, since the proposed switch provides an ultra-high off-resistance in the range of several GΩs, the leakage current of the proposed switch is negligible. Simulation results also show that switch induced errors are significantly eliminated by using the proposed cancellation technique. The output error charge due to charge injection and clock feed-through over a wide range of the input signal variation is less than 1.6fC. Moreover, simulation results show that the proposed switch achieves signal to noise plus distortion ratio (SNDR) of 80.55dB, effective number of bits (ENOB) of 13.08, total harmonic distortion (THD) of -81.41dB and spurious-free dynamic range (SFDR) of 87.7dB for a 2.5MHz sinusoidal input of 800mv peak-to-peak amplitude at 200MHz sampling rate with a 1.8V supply voltage.}, keywords = {Analog switch,channel charge injection,clock feed-through,sub-threshold leakage,switched capacitor circuit}, title_fa = {یک سوئیچ آنالوگ جدید برای مدارهای خازن سوئیچ‌شده دقت بالا}, abstract_fa = {عملکرد مدارهای خازن سوئیچ‌شده به میزان قابل توجهی به سوئیچ‌های آنالوگ مورد استفاده در آن‌ها وابسته است. خطاهای تزریق بار کانال، نفوذ کلاک و نشتی حالت خاموش اصلی‌ترین عوامل محدود‌کننده دقت این سوئیچ‌های آنالوگ هستند. در این مقاله روشی نوین برای کمینه‌کردن این خطاها با استفاده از ساختاری بسیار ساده معرفی شده است. برای ارزیابی عملکرد سوئیچ پیشنهادی، شبیه‌سازی‌ها با استفاده از فن‌آوری 0.18 μm انجام شده است. نتایج شبیه‌سازی‌ها نشان می‌دهند مقاومت روشن سوئیچ پیشنهادی در سراسر محدوده سیگنال ورودی کم‌تر از Ω560 می‌باشد که این میزان مقاومت مشخصات موردنیاز پهنای‌باند دنباله‌روی سوئیچ را به‌طور کامل برآورده می‌سازد. به‌علاوه، از آنجایی‌که مقاومت خاموش سوئیچ پیشنهادی بسیار زیاد (چند گیگااهم) است، جریان نشتی آن بسیار ناچیز می‌باشد. هم‌چنین شبیه‌سازی‌ها نشان می‌دهند که خطاهای ناشی از سوئیچ با استفاده از روش پیشنهادی به‌طور قابل ملاحظه‌ای کاهش یافته است. میزان بار خطای ایجاد شده در خروجی ناشی از تزریق بار و نفوذ کلاک در محدوده وسیعی از تغییرات ورودی کم‌تر از fC 1.6 می‌باشد. هم‌چنین سوئیچ پیشنهادی به ازای ورودی سینوسی با فرکانس MHz 2.5 و دامنه mV800 و نیز فرکانس کلاک MHz200 با ولتاژ تغذیهV 1.8 دارای SNDR برابر باdB 80.55، ENOB برابر با 13.08، THD برابر با dB -81.41 و SFDR برابر با dB 87.7 می‌باشد. }, keywords_fa = {سوئیچ آنالوگ,تزریق بار کانال,نفوذ کلاک,جریان زیر آستانه,مدارهای خازن سوئیچ‌شده}, url = {https://tjee.tabrizu.ac.ir/article_9146.html}, eprint = {https://tjee.tabrizu.ac.ir/article_9146_85a4300f0ab4fe49b64d4598ac0d2b58.pdf} } @article { author = {Vali, M. and Dideban, D. and Moezi, N.}, title = {Evaluation of Analog Performance and Short Channel Effect Parameters on Field Effect Transistor based on Topological Insulations}, journal = {TABRIZ JOURNAL OF ELECTRICAL ENGINEERING}, volume = {49}, number = {2}, pages = {925-933}, year = {2019}, publisher = {Faculty of Electrical & Computer Engineering}, issn = {2008-7799}, eissn = {2538-3051}, doi = {}, abstract = {In this paper, in order to evaluate new materials for design and simulation of the field effect transistors in nano dimensions, we simulate and investigate the electronic properties of a field effect transistor based of topological insulator. Since the energy gap in the channel region of this transistor is adjustable by a perpendicular magnetic field, first by obtaining the transfer characteristics, we analyze the DC characteristics such as Ion/Ioff ratio and the threshold voltage. Moreover, we evaluate the short channel effects (SCEs) including subthreshold slope (SS) and drain induced barrier lowering (DIBL).The obtained results for (SS) and (DIBL) for m=1 show the values of 8.24mV/dec and 0.064, respectively, which are very suitable for transistor applications. Finally we achieve the analog characteristics of the simulated field effect transistor such as transconductance, output conductance, output resistance and voltage gain and study the parameters affecting these figures of merits.}, keywords = {Field effect transistor,topological insulator,Ion/Ioff ratio,threshold voltage,short channel effects,subthreshold slope,analog characteristics,transconductance,output conductance,output resistance,voltage gain}, title_fa = {ارزیابی عملکرد آنالوگ و پارامترهای اثر کانال کوتاه روی ترانزیستور اثر میدان بر پایه عایق توپولوژیک}, abstract_fa = {در راستای ارزیابی مواد جدید برای طراحی و شبیه سازی ترانزیستورهای اثر میدان در ابعاد نانومتری، در این مقاله ویژگی‌های الکترونیکی ترانزیستور اثر میدان بر پایه عایق توپولوژیک شبیه‌سازی و بررسی می‌گردد. از آنجا که گپ انرژی در ناحیه کانال این ترانزیستور با استفاده از میدان مغناطیسی عمود قابل‌تنظیم می‌باشد، ابتدا با رسم نمودار جریان بر حسب ولتاژ گیت به‌ازای مقادیر مختلف میدان مغناطیسی عمود، مشخصه‌های جریان مستقیم (DC Characteristics) همچون نسبت جریان روشن به جریان خاموش و ولتاژ آستانه (Threshold voltage) و عوامل مؤثر بر این پارامترها تجزیه و تحلیل می‌گردد. سپس برای ارزیابی اثرات کانال کوتاه، دو پارامتر نوسان زیرآستانه (subthreshold slope) و میزان تنزل سد القاشده ناشی از ولتاژ درین (DIBL) مورد بررسی قرار می‌گیرد. نتایج به‌دست‌آمده برای (subthreshold slope) و (DIBL) به‌ازای مغناطش  به‌ترتیب مقادیرmV/dec 8.24 و 0.064 را نشان می‌دهد که برای کاربردهای ترانزیستوری بسیار مناسب می‌باشد. در نهایت مشخصه‌های آنالوگ (Analog Characteristics) ترانزیستور شبیه‌سازی‌شده، همچون ترارسانایی (Transconductance)، هدایت خروجی (Output conductance)، مقاومت خروجی (Output resistance) و بهره ولتاژ (Gain) به‌دست‌آمده و عوامل مؤثر بر این پارامترها مورد ارزیابی قرار می‌گیرد.}, keywords_fa = {ترانزیستور اثر میدان,عایق توپولوژیک,نسبت جریان روشن به جریان خاموش,ولتاژ آستانه,اثرات کانال کوتاه,نوسان زیرآستانه,مشخصه‌های آنالوگ,ترارسانایی,هدایت خروجی,مقاومت خروجی,بهره ولتاژ}, url = {https://tjee.tabrizu.ac.ir/article_9114.html}, eprint = {https://tjee.tabrizu.ac.ir/article_9114_f687aa0d37ceaf11a2804c8cfd8de946.pdf} } @article { author = {Yaribeygi, M. and Beygi, L.}, title = {Optical Power and Modulation Level Assignment in PCE-based GMPLS Control Plane}, journal = {TABRIZ JOURNAL OF ELECTRICAL ENGINEERING}, volume = {49}, number = {2}, pages = {935-947}, year = {2019}, publisher = {Faculty of Electrical & Computer Engineering}, issn = {2008-7799}, eissn = {2538-3051}, doi = {}, abstract = {The tremendous growth in the demand for high data-rates in optical networks makes efficient use of available bandwidth indispensable. Network's throughput can be improved by exploiting high-level modulation formats which allow the transmission of high data-rate and upgrading the quality of optical communication signal which degrades due to transmission impairments. The nonlinearity of optical fibers has been long recognized as one of the most overriding factors limiting the quality of optical communication signal. Accurate evaluation of nonlinearity in generalized multiprotocol label switching (GMPLS) optical networks is more complex and costly. In this paper, we present a novel heuristic joint routing, wavelength and power allocation method for path computation element (PCE) based architecture for GMPLS optical networks such that launch power of the lightpaths are updated continuously, thereby the minimum number of lightpaths are assigned to the demands. The Gaussian noise (GN) model is exploited to capture the nonlinear effect and we focus on maximizing the Shannon sum rate for network. In the DTG network compared to existing methods, numerical results demonstrate that the number of higher order modulation formats is increased and the network throughput is improved about 138.4 THz.}, keywords = {Optical network,lightpath,PCE-based GMPLS,gaussian noise model,power optimization,modulation,throughput}, title_fa = {تخصیص توان نوری و سطح مدولاسیون در شبکه‌های نوری با لایه کنترل توزیع‌یافته مبتنی بر محاسبه مسیر متمرکز}, abstract_fa = {رشد نمایی تقاضای ترافیک در شبکه‌های نوری لزوم استفاده بهینه از پهنای باند را دربرداشته‌است. افزایش ظرفیت شبکه با بهبود کیفیت سیگنال‌های نوری و امکان انتقال نرخ داده بیشتر با تخصیص مدولاسیون‌های سطح بالا تحقق می‌یابد. از عوامل مهم کاهش کیفیت سیگنال‌های نوری، اثرهای غیرخطی است که محاسبه دقیق آن در شبکه‌های نوری با لایه کنترل توزیع‌یافته ضمن افزایش پیچیدگی با صرف هزینه زیادی همراه است. در این مقاله برای شبکه‌های نوری با لایه کنترل متمرکز یک الگوریتم محاسبه مسیر جدید با درنظرگرفتن مدل نویز گوسی برای بیان اثرهای غیرخطی ارائه می‌شود که علاوه‌بر تخصیص طول موج با روش ابتکاری، توان مسیرهای نوری در هر لحظه با هدف بیشینه‌سازی نرخ شانون در کل شبکه، به‌روزرسانی شده تا با تخصیص مدولاسیون‌های سطح بالا، به هر درخواست حداقل مسیر نوری ممکن تخصیص داده شود. نتایج شبیه‌سازی روی شبکه DTG نشان می‌دهد که در مقایسه با روش‌های موجود تعداد مدولاسیون‌های سطح بالا بیشتر شده و گذردهی شبکه به‌طور متوسط به اندازه THz 138.4 افزایش می‌یابد.}, keywords_fa = {شبکه‌های نوری,مسیر نوری,لایه کنترل متمرکز,مدل نویز گوسی,بهینه‌سازی توان,مدولاسیون,گذردهی}, url = {https://tjee.tabrizu.ac.ir/article_9121.html}, eprint = {https://tjee.tabrizu.ac.ir/article_9121_126dea0e769554aa5ac3fa74d1fdaabb.pdf} }